Dell Force10 MXL Blade Reference Manual Download Page 608

Page: 608 / 732

608

Storm Control

www.dell.com | support.dell.com

Parameters

Defaults

none

Command Modes

CONFIGURATION (conf)

Command

History

Usage

Information

Broadcast storm control is valid on Layer 2/Layer 3 interfaces only. Layer 2 broadcast traffic is treated
as unknown-unicast traffic.

storm-control broadcast (Interface)

Configure the packets per second of broadcast traffic to be limited on the interface.

Syntax

storm-control broadcast [

packets_per_second

] in

To disable broadcast storm control on the interface, use the

no storm-control broadcast

[

packets_per_second

] in

command.

Parameters

Defaults

none

Command Modes

INTERFACE (conf-if-

interface

slot/port

)

Command

History

storm-control multicast (Configuration)

Configure the packets per second (pps) of multicast traffic.

Syntax

storm-control multicast [

packets_per_second

] in

To disable storm-control for multicast traffic into the network, use the

no storm-control multicast

[packets_per_second]

command.

Parameters

Defaults

none

Command Modes

CONFIGURATION (conf)

Command

History

packets_per_second

Enter the packets per second of broadcast traffic allowed from the network.

Range: 0 to 33554368.

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

packets_per_second

Enter the packets per second of broadcast traffic allowed from the network.

Range: 0 to 33554368

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

packets_per_second

Enter the packets per second of multicast traffic allowed from the network
followed by the keyword

Range: 0 to 33554368

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

Summary of Contents for Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Force10 MXL Blade

Reviews:

Related manuals for Force10 MXL Blade

Brands by name

Popular brands

Dell Force10 MXL Blade, Reference Manual

Search results

Summary of Contents for Force10 MXL Blade

Reviews:

Related manuals for Force10 MXL Blade

Brands by name

Popular brands