Dell Force10 MXL Blade Reference Manual Download Page 698

Page: 698 / 732

698

SNMP Traps

www.dell.com | support.dell.com

RESV

NONE

N/A

CHM_MIN_ALRM_TEMP

ENVMON

TEMP

%CHMGR-2-MINOR_TEMP: Minor alarm: chassis temperature

CHM_MIN_ALRM_TEMP_CLR

ENVMON

TEMP

%CHMRG-5-MINOR_TEMP_CLR: Minor alarm cleared: chassis temperature normal (%s %d temperature is within threshold of %dC)

CHM_MAJ_ALRM_TEMP

ENVMON

TEMP

%CHMGR-2-MAJOR_TEMP: Major alarm: chassis temperature high (%s temperature reaches or exceeds threshold of %dC)

CHM_MAJ_ALRM_TEMP_CLR

ENVMON

TEMP

%CHMGR-2-MAJOR_TEMP_CLR: Major alarm cleared: chassis temperature lower (%s %d temperature is within threshold of %dC)

TME_TASK_SUSPEND

ENVMON

NONE

%TME-2-TASK SUSPENDED: SUSPENDED - svce:%d - inst:%d - task:%s

TME_TASK_TERM

ENVMON

NONE

%TME-2-ABNORMAL_TASK_TERMINATION: CRASH - task:%s %s

CHM_CPU_THRESHOLD

ENVMON

NONE

%CHMGR-5-CPU_THRESHOLD: Cpu %s usage above threshold. Cpu5SecUsage (%d)

CHM_CPU_THRESHOLD_CLR

ENVMON

NONE

%CHMGR-5-CPU_THRESHOLD_CLR: Cpu %s usage drops below threshold. Cpu5SecUsage (%d)

CHM_MEM_THRESHOLD

ENVMON

NONE

%CHMGR-5-MEM_THRESHOLD: Memory %s usage above threshold. MemUsage (%d)

CHM_MEM_THRESHOLD_CLR

ENVMON

NONE

%CHMGR-5-MEM_THRESHOLD_CLR: Memory %s usage drops below threshold. MemUsage (%d)

MACMGR_STN_MOVE

ENVMON

NONE

%MACMGR-5-DETECT_STN_MOVE: Station Move threshold exceeded for Mac %s in vlan %d

VRRP_BADAUTH

PROTO

NONE

%RPM1-P:RP2 %VRRP-3-VRRP_BAD_AUTH: vrid-1 on TenGig 11/12 rcvd pkt with authentication type mismatch.

%RPM1-P:RP2 %VRRP-3-VRRP_BAD_AUTH: vrid-1 on TenGig 11/12 rcvd pkt with authentication failure.

VRRP_GO_MASTER

PROTO

NONE

%VRRP-6-VRRP_MASTER: vrid-%d on %s entering MASTER

VRRP_PROTOCOL_ERROR

PROTO

NONE

VRRP_PROTOERR: VRRP protocol error on %S

BGP4_ESTABLISHED

PROTO

NONE

%TRAP-5-PEER_ESTABLISHED: Neighbor %a, state %s

BGP4_BACKW_XSITION

PROTO

NONE

%TRAP-5-BACKWARD_STATE_TRANS: Neighbor %a, state %s

ETS_TRAP_TYPE_MODULE_STATUS_CHA
NGE

ETS

NONE

%DIFFSERV-5-ETS_TRAP_TYPE_MODULE_STATUS_CHANGE: ETS Module status changed to enabled

Table 41-1. SNMP Traps and Error Messages (continued)

Message ID

Trap Type

Trap Option

Summary of Contents for Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Force10 MXL Blade

Reviews:

Related manuals for Force10 MXL Blade

Brands by name

Popular brands

Dell Force10 MXL Blade, Reference Manual

Search results

Summary of Contents for Force10 MXL Blade

Reviews:

Related manuals for Force10 MXL Blade

Brands by name

Popular brands