manualshive.com logo in svg

Dell Force10 MXL Blade, Reference Manual

Share
Download
Dell Force10 MXL Blade Reference Manual Download Page 436

436

|

Port Monitoring

www.dell.com | support.dell.com

show running-config monitor session 

Display the running configuration of all monitor sessions or a specific session.

Syntax

show running-config monitor session {

session-ID

}

To display the running configuration for all monitor sessions, use just the 

show running-config 

monitor session 

command.

Parameters

 

Defaults

none

Command Modes

EXEC

EXEC Privilege

Command

History

Example

Figure 22-4.  show running-config monitor session Command Example

Usage

Information

The 

monitoring

 command is saved in the running configuration at the Monitor Session mode level and 

can be restored after a chassis reload.

Related

Commands

 

session-ID

(OPTIONAL) Enter a session identification number.

Range: 0 to 65535

Version 8.3.16.1

Introduced on M I/O Aggregator

FTOS#show running-config monitor session 
!
monitor session 8
 source TenGigabitEthernet 10/46 destination TenGigabitEthernet 10/1 direction rx
!
monitor session 11
 source TenGigabitEthernet 10/0 destination TenGigabitEthernet 10/47 direction rx

FTOS#show running-config monitor session 11
!
monitor session 11
 source TenGigabitEthernet 10/0 destination TenGigabitEthernet 10/47 direction rx

monitor session

Creates a session for monitoring.

show monitor session

Displays a monitor session.

Summary of Contents for Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands