manualshive.com logo in svg

Dell Force10 MXL Blade, Reference Manual

Share
Download
Dell Force10 MXL Blade Reference Manual Download Page 574

574

|

sFlow

www.dell.com | support.dell.com

sflow extended-switch enable 

Enable packing information on a switch only.

Syntax

sflow extended-switch

 

enable

To disable packing information, use the 

no sflow extended-switch

 [

enable

] command.

Parameters

 

Defaults

Disabled

Command Modes

CONFIGURATION

Command

History

Usage

Information

FTOS version 7.8.1.0 and later enhances the sflow implementation for real time traffic analysis to 
provide extended gateway information in cases where the destination IP addresses are learned by 
different routing protocols and for cases where the destination is reachable over ECMP.

 

Related

Commands

 

sflow polling-interval (Global)

Set the sFlow polling interval at a global level.

Syntax

sflow polling-interval 

interval value

To return to the default, use the 

no sflow polling-interval 

interval

 command.

Parameters

 

Defaults

20 seconds

Command Modes

CONFIGURATION

Command

History

Usage

Information

The polling interval for an interface is the maximum number of seconds between successive samples of 
counters to be sent to the collector. This command changes the global default counter polling (20 seconds) 
interval. You can configure an interface to use a different polling interval.

Related

Commands

 

enable

Enter the keyword 

enable

 to enable global extended information. 

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

show sflow

Displays the sFlow configuration

interval value

Enter the interval value in seconds.

Range: 15 to 86400 seconds

Default: 20 seconds

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

sflow polling-interval (Interface)

Sets the polling interval for an interface

Summary of Contents for Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands