manualshive.com logo in svg

Dell Force10 MXL Blade, Reference Manual

The Dell Force10 MXL Blade is a cutting-edge network switch designed for high-performance data centers. Unlock its full potential by easily configuring its advanced features through our comprehensive and user-friendly manual, available for free download at manualshive.com. Empower your network infrastructure today with this unparalleled product.

Share
Download
background image

672

|

Virtual Router Redundancy Protocol (VRRP)

www.dell.com | support.dell.com

virtual-address

Configure up to 12 IP addresses of virtual routers in the VRRP group. You must set at least one virtual 
address for the VRRP group to start sending VRRP packets. 

Syntax

virtual-address

 

ip-address1

 [... 

ip-address12

]

To delete one or more virtual IP addresses, use the 

no

 

virtual-address

 

ip-address1

 [... 

ip-address12

] 

command.

Parameters

 

Defaults

Not configured.

Command Modes

VRRP

Command

History

Usage

Information

The VRRP group only becomes active and sends VRRP packets when a virtual IP address is 
configured. When you delete the virtual address, the VRRP group stops sending VRRP packets.

A system message appears after you enter or delete the 

virtual-address

 command.

To guarantee that a VRRP group becomes MASTER, configure the VRRP group’s virtual address with 
the same IP address as the interface’s primary IP address and change the 

priority

 of the VRRP group to 

255.

You can ping the virtual addresses configured in all VRRP groups.

vrrp delay minimum 

Set the delay time for VRRP initialization after an interface comes up.

Syntax

vrrp delay minimum 

seconds

Parameters

 

Defaults

0

Command Modes

INTERFACE

Command

History

ip-address1

Enter an IP address of the virtual router in dotted decimal format. 

The IP address must be on the same subnet as the interface’s primary IP address.

... 

ip-address12

(OPTIONAL) Enter up to 11 additional IP addresses of virtual routers in dotted 
decimal format. Separate the IP addresses with a space. 

The IP addresses must be on the same subnet as the interface’s primary IP address.

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

seconds

Enter the number of seconds for the delay for VRRP initialization after an interface 
becomes operational.

Range: 0 to 900 (0 indicates no delay)

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

Summary of Contents for Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Force10 MXL Blade

NEC Express5800/T110g-S Configuration Manual preview
Express5800/T110g-S
Brand: NEC Pages: 34
Dot Hill AssuredSAN 4004 Series Fru Installation And Replacement Manual preview
AssuredSAN 4004 Series
Brand: Dot Hill Pages: 59
B&B Electronics VESR4x4 Quick Start Manual preview
VESR4x4
Brand: B&B Electronics Pages: 2
RaidSonic IB-NAS4210-B Brochure & Specs preview
IB-NAS4210-B
Brand: RaidSonic Pages: 2
Motorola WPS870G - Wireless Print Server User Manual preview
WPS870G - Wireless Print Server
Brand: Motorola Pages: 115
SEH PS107 Quick Installation Manual preview
PS107
Brand: SEH Pages: 32
Transition Networks SDSTX3110-121S-LRT User Manual preview
SDSTX3110-121S-LRT
Brand: Transition Networks Pages: 109
AAxeon STW-602C User Manual preview
STW-602C
Brand: AAxeon Pages: 74
Promise Technology Smartstor NS4600 Product Manual preview
Smartstor NS4600
Brand: Promise Technology Pages: 370
Solid DMS-1200 Operation Manual preview
DMS-1200
Brand: Solid Pages: 102
Intel SR1530CL - Server System - 0 MB RAM User Manual preview
SR1530CL - Server System - 0 MB RAM
Brand: Intel Pages: 188
Digitus DN-7025 Quick Installation Manual preview
DN-7025
Brand: Digitus Pages: 8
3onedata CP202-2CI Quick Installation Manual preview
CP202-2CI
Brand: 3onedata Pages: 3
Intel S815EBM1 - Server Board Motherboard Product Manual preview
S815EBM1 - Server Board Motherboard
Brand: Intel Pages: 76
Lantronix WiBox User Manual preview
WiBox
Brand: Lantronix Pages: 74
Oracle SPARC T7-4 Service Manual preview
SPARC T7-4
Brand: Oracle Pages: 208
Gateway GT350 F1 Specifications preview
GT350 F1
Brand: Gateway Pages: 17
Gateway 910 Series System Manual preview
910 Series
Brand: Gateway Pages: 129

Brands by name

Popular brands

Load more brands