manualshive.com logo in svg

Dell Force10 MXL Blade, Reference Manual

Share
Download
Dell Force10 MXL Blade Reference Manual Download Page 261

Interfaces |

261

Input Statistics:

Displays all the input statistics including: 

•

Number of packets and bytes into the interface

•

Number of packets with IP headers and VLAN tagged headers.

Note: 

The sum of the number of packets may not be as expected 

since a VLAN tagged IP packet counts as both a VLAN packet and an 
IP packet. 

•

Packet size and the number of those packets inbound to the interface

•

Number of symbol errors, runts, giants, and throttles packets:

symbol errors = number packets containing bad data. That is, the port 
MAC detected a physical coding error in the packet.

runts = number of packets that are less than 64B 

giants = packets that are greater than the MTU size 

throttles = packets containing PAUSE frames 

•

Number of CRC, IP Checksum, overrun, and discarded packets:

CRC = packets with CRC/FCS errors 

IP Checksum = packets with IP Checksum errors 

overrun = number of packets discarded due to FIFO overrun conditions 

discarded = the sum of input symbol errors, runts, giants, CRC, IP 
Checksum, and overrun packets discarded without any processing 

Output Statistics:

Displays output statistics sent out of the interface including:

•

Number of packets, bytes and underruns out of the interface

packets = total number of packets

bytes = total number of bytes 

underruns = number of packets with FIFO underrun conditions

•

Number of Multicast, Broadcast and Unicast packets:

Multicasts = number of MAC multicast packets 

Broadcasts = number of MAC broadcast packets 

Unicasts = number of MAC unicast packets

•

Number of throttles and discards packets:

throttles = packets containing PAUSE frames 

discarded = number of packets discarded without any processing 

Rate information...

Estimate of the input and output traffic rate over a designated interval (30 to 
299 seconds).

Traffic rate is displayed in bits, packets per second, and percent of line rate. 

Time since...

Elapsed time since the last interface status change (hh:mm:ss format). 

Table 14-5.  Lines in show interfaces Command Example

Line

Description

Summary of Contents for Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands