D-Link NetDefendOS User Manual Download | Manualshive

Page: 352 / 912

background image

For the IPv4 address of the router, we simply use any single IP address from the network

192.168.55.0/24

. For example,

192.168.55.1

.

When NetDefendOS sets up OSPF, it will look at this

OSPF Neighbor

object and will try to send

OSPF messages to the IPv4 address

192.168.55.1

. The

OSPF Interface

object defined in the

previous step tells NetDefendOS that OSPF related traffic to this IP address should be routed into
the IPsec tunnel.

5. Set the Local IP of the tunnel endpoint

To finish the setup for firewall A there needs to be two changes made to the IPsec tunnel setup
on firewall B. These are:

i.

In the IPsec tunnel properties, the Local Network for the tunnel needs to be set to

all-nets

.

This setting acts as a filter for what traffic is allowed into the tunnel and

all-nets

will allow all

traffic into the tunnel.

ii.

In the routing section of the IPsec properties, the Specify address manually option needs
to be enabled and the IPv4 address in this example of

192.168.55.1

needs to be entered (in

the CLI,

OriginatorType

is set to manual and the

OriginatorIP

is

192.168.55.1

). This sets the

tunnel endpoint IP to be

192.168.55.1

so that all OSPF traffic will be sent to firewall A with

this source IP.

The result of doing this is to "core route" OSPF traffic coming from firewall A. In other words, the
traffic is destined for NetDefendOS.

6. Repeat the steps for the other firewall

What we have done so far is allow OSPF traffic to flow from A to B. The steps above need to be
repeated as a mirror image for firewall B using the same IPsec tunnel. The same random internal
IP network for OSPF setup should be used on both A and B.

Tip: Non-OSPF traffic can also use the tunnel

A VPN tunnel can carry both OSPF traffic as well as other types of traffic. There is no
requirement to dedicate a tunnel to OSPF traffic.

4.6.6. An OSPF Example

This section goes through the detailed setup steps for the simple OSPF scenario illustrated
below.

Chapter 4: Routing

352

«
...
350
351
352
353
354
...
»

Summary of Contents for NetDefendOS

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for NetDefendOS

NetDefend DFL-800

Brand: D-Link Pages: 21

Brand: Advantech Pages: 25

Data Loss Prevention Prevent

Brand: McAfee Pages: 8

Brand: Fortinet Pages: 24

Brand: Nexcom Pages: 66

Brand: Ronde & Schwarz Pages: 129

Brand: PaloAlto Networks Pages: 30

Brand: Lanner Pages: 84

NG Firewall F18

Brand: Barracuda Pages: 5

Brand: D-Link Pages: 213

ZyXEL ZyWALL USG-1000

Brand: ZyXEL Communications Pages: 986

Brand: Billion Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands