Canon imagePRESS C800 Series, Troubleshooting Manual

Page: 225 / 256

Chapter 1
1-211
1.1.7.1.78 How to set refresh level of Fixing Belt
0031-6908
[ Manual-related ]
Description
Please explain how to set the refresh level of Fixing Belt.
Field Remedy
In following service mode, the refresh level of Fixing Belt can be changed.
1) Select Service Mode (Level 2) > COPIER > OPTION > USER > FX-CLNLV.
[Reference] If long-width paper is printed after printing a large quantity of short width paper, light glossy lines may occur with the same width as short-width paper
in the feed direction. The auto refresh control of the Fixing Belt is performed to prevent glossy lines, but use this mode when this symptom still occurs.
2) Enter the setting value, press OK key, and turn OFF and then ON the main power switch.
- Setting value: -5 to 5 (default: 0)
- Switch negative/positive by -/+ key
[Caution] As the value is increased, the effect of refresh control is improved, but the life of the Fixing Belt is shortened. Also, there is a possibility that the Fixing
Belt may be damaged.
[Reference] When Service Mode > COPIER > OPTION > DSPLY-SW > IMGC-ADJ is set to "1", Fixing Belt Auto Refresh Level can also be set in Settings/
Registration.
- Settings/Registration > Adjustment/Maintenance > Fixing Belt Auto Refresh Level
1.1.7.1.79 How to check total counter values of Fixing Belt Unit/Pressure Belt Unit
0031-6909
[ Manual-related ]
Description
Please explain how to check total counter values of Fixing Belt Unit and Pressure Belt Unit.
Field Remedy
Total counter values of Fixing Belt Unit and Pressure Belt Unit can be checked from parts counters in service mode.
a) Fixing Belt Unit parts counter
Service Mode > COPIER > COUNTER > DRBL-1 > FX-BLT-U
- 1st line: Total counter value from the previous replacement
- 2nd line: Estimated life value
- Setting value: 0 to 99999999 (Default value: 0)
- To clear the counter value, select the item and then press Clear key.
- To change the estimated life, select the item, enter the value and then press OK key.
[Caution]
- Clear the counter value after replacement.
- When the counter value is cleared, the values of FX-U-TM1 to 5, FXU-STR, FX1-RFRL, FX-RF-RL and FX-R-TM are also cleared.
b) Pressure Belt Unit parts counter
Service Mode > COPIER > COUNTER > DRBL-1 > FX-BLT-L
- 1st line: Total counter value from the previous replacement
- 2nd line: Estimated life value
- Setting value: 0 to 99999999 (default: 0)
- To clear the counter value, select the item and then press Clear key.
- To change the estimated life, select the item, enter the value and then press OK key.
[Caution]
- Clear the counter value after replacement. If not cleared, E008-0001 may occur.
- When the counter value is cleared, the log of current value of the Fixing Motor is also cleared.
- When E008-0001 occurs and this is handled without replacement of the Pressure Belt Unit, be sure to clear the log of the Fixing Motor current values in service
mode. If you don't, E008-0001 will occur again.
- Service Mode > COPIER > Function > Clear > FX-L-CLR (Clear of Fixing Motor current value log)
1.1.7.1.80 Points to note when replacing HDD
0031-7151
[ Manual-related ]
Description
Please explain necessary remedies when replacing the HDD.
Description
Please explain necessary remedies when replacing the HDD.
Field Remedy
a) Before Replacing
1) Backup following data by the remote UI.
Remote UI > Settings/Registration > Management Settings > Data Management > Back Up
Target data:
- Mail Box
- Memory RX Inbox
- Confidential Fax Inbox
- Form for Composition
[Reference] When the optional HDD (1TB) is used, the backup is possible only with an USB connected HDD.
2) Backup following data by the remote UI.
Remote UI > Settings/Registration > Management Settings > Data Management > Import/Export All > Export
Target data:
- Settings/Registration Basic Information
- Paper Type Management Settings
- Forwarding Settings
- Box Settings
- Department ID Management Settings
- Main Menu Settings
- Web Access Settings
- Favorite Settings
- Address Book
- Quick Menu Settings
- MEAP Application Setting Information