YASKAWA CIPR-GA50C series, Техническое руководство

Страница: 604 / 766

12.8 H: Terminal Function Selection
604 YASKAWA SIEPC71061753A GA500 Technical Manual
■
2: External Reference 1/2 Selection
Setting Value Function Description
2 External Reference 1/2
Selection
Sets the drive to use Run command source 1/2 or Reference command source 1/2 when in REMOTE Mode.
Note:
When the drive is receiving a Run command, you cannot switch between reference sources.
ON : b1-15 = [Frequency Reference Selection 2], b1-16 [Run Command Selection 2]
OFF : b1-01 = [Frequency Reference Selection 1], b1-02 [Run Command Selection 1]
■
3: Multi-Step Speed Reference 1
Setting Value Function Description
3 Multi-Step Speed Reference
1
Uses speed references d1-01 to d1-16 to set a multi-step speed reference.
Note:
Refer to “ Setting Procedures for Multi-step Speed Operation ” in “ d: Reference Settings ” for more information.
■
4: Multi-Step Speed Reference 2
Setting Value Function Description
4 Multi-Step Speed Reference
2
Uses speed references d1-01 to d1-16 to set a multi-step speed reference.
Note:
Refer to “ Setting Procedures for Multi-step Speed Operation ” in “ d: Reference Settings ” for more information.
■
5: Multi-Step Speed Reference 3
Setting Value Function Description
5 Multi-Step Speed Reference
3
Uses speed references d1-01 to d1-16 to set a multi-step speed reference.
Note:
Refer to “ Setting Procedures for Multi-step Speed Operation ” in “ d: Reference Settings ” for more information.
■
6: Jog Reference Selection
Setting Value Function Description
6 Jog Reference Selection
Sets the drive to use the JOG Frequency Reference (JOG command) set in d1-17 . The JOG Frequency Reference (JOG
command) overrides Frequency References 1 to 16 (d1-01 to d1-16) .
■
7: Accel/Decel Time Selection 1
Setting Value Function Description
7 Accel/Decel Time Selection
1
Sets the drive to use
Acceleration/Deceleration Time 1 [C1-01, C1-02]
or
Acceleration/Deceleration Time 2 [C1-03, C1-04]
.
Note:
Refer to
“
C1: Accel & Decel Time
”
for more information.
■
8: Baseblock Command (N.O.)
Setting Value Function Description
8 Baseblock Command
(N.O.)
Sets the command that stops drive output and coasts the motor to stop when the input is ON.
The keypad flashes bb [Baseblock] . If you cancel the baseblock command when the Run command is active, the
drive will restart the motor and use the speed search function.
WARNING! Sudden Movement Hazard. When you use a mechanical holding brake with the drive in a lifting application, you
must close the brake if an input terminal triggers the Baseblock command to stop drive output. If you enter the baseblock
command, the motor will suddenly coast and the load will slip, which can cause serious injury or death.
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV
V/f OLV OLV/PM OLV/PM AOLV/PM EZOLV