Toshiba Estia RUA-CP1701H, Руководство по обслуживанию

Страница: 122 / 164

Monobloc Outdoor Unit Service Manual
121
10.1.5.2. Air Setpoint Table
Access type: Read/Write
TABLE NAME: AIR_STP, PIC Table Type: 17H, instance 2
PAR. NAME RANGE DEFAULT UNIT DESCRIPTION
421 htoccstp 12.0 to 34.0 19.0 °C Heat Home Setpoint
1
422 htunooff -10.0 to 0.0 -2.0 ^C Heat Sleep Offset
1, 2
423 htecooff -10.0 to 0.0 -4.0 ^C Heat Away Offset
1, 3
424 cloccstp 20.0 to 38.0 26.0 °C Cool Home Setpoint
1
425 clunooff 0.0 to 10.0 2.0 ^C Cool Sleep Offset
1, 2
426 clecooff 0.0 to 10.0 4.0 ^C Cool Away Offset
1, 3
427 freezstp 6.0 to 12.0 6.0 °C Home AntiFreeze Setpoint
4
428 deltastp 0.2 to 1.0 0.5 ^C Air Delta Setpoint
5
429 iat_fact 0.0 to 2.0 0.0 - IAT Reset Factor
6
1. Occupancy modes
Occupancy Comfort Type
Home Comfort
Sleep Comfort
Away Eco
2. Sleep offset
The offset applied to the Home setpoint.
3. Away offset
The offset applied to the Home setpoint.
4. Anti-freeze setpoint
This is the minimum room temperature that is allowed.
If room temperature drops below this setpoint, the unit will
start to operate in Heating mode.
5. Air delta setpoint
This parameter is used to determine whether the control
is in cooling or heating demand.
6. IAT reset factor
This parameter is used to determine the indoor air
temperature.
10.1.6.
POC tables
POC tables are used to control Follower units that are interconnected to operate in the same Header /
Follower assembly.
10.1.6.1. Follower 0 Status Table
Access type: Read-only
TABLE NAME: SLV0STAT, PIC Table Type: 615H, instance 1
PAR. NAME RANGE DEFAULT UNIT DESCRIPTION
1001 ewt xx.x - °C Entering Water Temp
1002 lwt xx.x - °C Leaving Water Temp
1003 mod_stat 0 to 101 - - System Mode Status
1
1004 alm Normal/Alarm - - Alarm Status
1005 cap_t 0 to 100 - % Total Capacity
1006 cap_ovr 0 to 204 - - Capacity Override
1007 pmp 0 to 100 - % Water Pump Speed
1008 pmp_ovr -1 to 100 - - Pump Override
1009 flow_sw Close/Open - - Flow Switch Status
1010 freq_cur 0 to 120 - Hz Actual Compressor Freq
1011 wearfact xxxxxxxx - - Unit Wear Factor
2
1. System Mode Status
-1 = Disabled
0 = Off
1 = Cool
2 = Heat
3 = unused
4 = DHW (Heat)
5 = Booster Cooling
6 = Booster Heating
7 = Defrost
8 = Purge
9 = Drying 20 = Home Anti-Freeze
21 = Cool Satisfied
22 = Heat Satisfied
24 = DHW Satisfied
29 = Drying Satisfied
100 = Not Responding
101 = Failed
2. Unit wear factor
The unit wear factor is calculated based on the number of
operating hours of the compressor as well as the number
of starts of the compressor