Toshiba Estia RUA-CP1701H Скачать руководство пользователя страница 113 | Manualshive

Страница: 113 / 164

background image

Monobloc Outdoor Unit Service Manual

112

10.1.3.7. DHW Status Table

Access type: Read-only (force is possible)

TABLE NAME: DHW_STAT, PIC Table Type: 11H, instance 7

PAR.

NAME

RANGE

DEFAULT

UNIT

DESCRIPTION

201

DHW_MODE

0 to 2

-

-

DHW Mode

1

202

dhw_ovr

-1 to 100

-

-

DHW Override

2

203

dhw_dem

No / Yes

-

-

DHW Demand from Tank

204

dhw_cond

True / False

-

-

DHW Conditions

3

205

DHW_CTLP

20.0 to 60.0

-

°C

DHW Control Point

206

DHW_TT

-40.0 to 115.6

-

°C

DHW Tank Temperature

207

shc_time

xxx

-

min

Current SHC Runtime

208

dhw_time

xxx

-

min

Current DHW Runtime

209

DHW_EXCP

0 to 1440

-

min

DHW Exception Timer

114

DHW_REQ

Open / Close

-

-

DHW Request from Tank

4

115

DHW_PRIO

Open / Close

-

-

DHW Priority Button

4

116

DHW_ANTI

Open / Close

-

-

DHW Anti-Legionella Req.

4

117

SUMM_SW

Open / Close

-

-

Summer Switch

4

210

DHW_VLV

Off / On

-

-

DHW Diverting Valve

5

211

DHW_EHS

Off / On

-

-

DHW Elec Heat Stage

212

DHW_RUN

No / Yes

-

-

DHW Running Status

1. DHW mode
0 = DHW Eco mode
1 = DHW anti-legionella mode
2 = DHW regular mode

2. DHW override
-1 = DHW disabled
0 = DHW Operating
1 = DHW Not Operating (Space Heating / Cooling Mode)
2 = DHW Valve moving
3 = DHW Operating with EHS Only
50 = Heat Mode not allowed
100 = DHW Fail

3. DHW conditions
DHW conditions are met (and the flag is set) if the unit is
not in DHW alarm and one of the following conditions is
true:

● DHW only mode is selected

● Summer mode is active (heat pumps only)

● DHW schedule is active

● DHW priority switch is closed

Note

: The unit is allowed to switch into DHW Mode only

when both “DHW Demand from Tank” [P203] and “DHW
Conditions” [P204] are set to "Yes" / "True".

4. Virtual switches
These switches do not correspond to real Discrete Inputs.
Their statuses are mapped to the DI#5 to 8 customized
(see §3.6.2. General electrical connection on terminal
block X2 )
They can be accessed through JBus Registers regardless
of the General Purpose Switches configuration.

5. DHW Diverting Valve
This is the status of the signal sent to the valve in
accordance with the DHW Valve Type configuration
[P701].

«
...
111
112
113
114
115
...
»

Содержание Estia RUA-CP1701H





































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Estia RUA-CP1701H

Бренд: Maag Страницы: 16

Бренд: Waterous Страницы: 13

Бренд: Waterous Страницы: 8

Бренд: L.B. White Страницы: 81

Бренд: Daitsu Страницы: 50

Бренд: Eliz Страницы: 20

Бренд: HeatStar Страницы: 60

Бренд: PerformancePro Страницы: 15

Бренд: Cozy Products Страницы: 2

Бренд: Salton Страницы: 7

Бренд: Day and Night Страницы: 18

Бренд: Toyostove Страницы: 18

Бренд: S+H Nolting Страницы: 35

Бренд: kayami Страницы: 28

Бренд: Daikin Страницы: 40

Elnur ECOMBI HHR Series

Бренд: Gabarron Страницы: 17

Бренд: Honda Страницы: 25

Бренд: Sulzer Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды