Toshiba Estia RUA-CP1701H Скачать руководство пользователя страница 81

Страница: 81 / 164

Monobloc Outdoor Unit Service Manual

9.4.1.3.

Alarms 10 to 14 – Temperature sensors on inverter board

Electrical connection

Alarm 10

Discharge Temperature (TD) sensor failure

CN603 on MCC-1599

Alarm 11

Lower Air Temperature (TE) sensor failure

CN601 on MCC-1599

Alarm 12

Upper Air Exchanger Temperature (TL) sensor failure

CN604 on MCC-1599

Alarm 13

TO sensor failure

CN602 on MCC-1599

Alarm 14

Suction Temperature (TS) sensor failure

CN600 on MCC-1599

9.4.1.4.

Alarm 15 – Inverter heatsink temperature sensor failure

The sensor is located on the heatsink of the inverter box, it is not accessible.

Alarm 15

UI Indoor Temperature failure

If a failure occurs on the TH temperature sensor, then the inverter box must be changed:

9.4.1.5.

Alarm 16 – Inverter TE & TS sensors wrongly connected

Electrical connection

Alarm 16

Inverter TE & TS sensors wrongly connected

For TE: CN601 on MCC-1599
For TS: CN600 on MCC-1599

Change WUI (RC – remote controller)

Is sensor mounting correctly?

Are the resistance
characteristics of the
temperature sensor normal?
(check with resistance curve)

Replace defective sensor

Correct sensor mounting

Check inverter box and replace if defective

YES

Is sensor correctly connected?
(refer to wiring diagram

Are the resistance
characteristics of the
temperature sensor normal?
(check with resistance curve)

Replace defective sensor

Correctly connect the sensor

Check inverter box and replace if defective

YES

Содержание Estia RUA-CP1701H





































































































































































Результаты поиска

Содержание Estia RUA-CP1701H

Отзывы:

Похожие инструкции для Estia RUA-CP1701H

Бренды по названию

Популярные бренды

Toshiba Estia RUA-CP1701H, Руководство по обслуживанию

Результаты поиска

Содержание Estia RUA-CP1701H

Отзывы:

Похожие инструкции для Estia RUA-CP1701H

Бренды по названию

Популярные бренды