Toshiba Estia RUA-CP1701H Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 164

background image

Monobloc Outdoor Unit Service Manual

52

Operating Mode

Conditions

Action

DHW Mode

Heat demand exists

Pump is running

Heat satisfied and Pump Logic = 1 “Always ON”

Pump is running

Heat satisfied and Pump Logic = 2 “Water Sampling”

Pump is running periodically

Cooling Mode

Cool demand exists

Pump is running

Cool satisfied and Pump Logic = 1 “Always ON”

Pump is running

Cool satisfied and Pump Logic = 2 “Water Sampling”

Pump is running periodically

Purge Mode

The flow switch status is not taken in account

Pump is running

Defrost mode

-

Pump is running

Header / Follower

Header/Follower Pump type (Par. 758) is used to define pump control for units
operating in the assembly:
0 = No pump control
1 = Common Water Pump; a pump is installed outside the unit on the water loop and
it is controlled by the Header
2 = Individual Water Pump: Running according to the Header/Follower overall status
(Par. 229); each Header or Follower unit has its own pump
3 = Individual Water Pump: Pump is stopped when the unit is satisfied.

•

No Internal Pump Option (pmp_type = 0)

If no internal main pump is fitted then parameter [P804] = 0. There are 2 control options for the no internal main pump
configuration:

•

Either the external main pump is not controlled by the unit and

External Main Pump Control

parameter

[P561]

is set to

“No” (0)

(then the pump relay of the NHC board is forced to off)

OR

•

The external main pump is controlled by the unit and the External Main Pump Control parameter

[P561]

is set

to "Yes" (1) (then the pump relay of the NHC board can be used to control an external (customer) pump).

Note: The External Main Pump Ctrl parameter [P561] is only enable the Factory set parameter [P804] is set to 0 (no
internal pump available)

It is recommended to control the external pump using a relay / contactor connected to TB X2, on the Monobloc
outdoor unit, as shown below:

Related

Parameters for external main pump control:

Par.No

Description

Range

Default

561

External main pump control – (pmp_ext):

0 ~ 1

0

«
...
51
52
53
54
55
...
»

Содержание Estia RUA-CP1701H





































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Estia RUA-CP1701H

Бренд: Pelonis Страницы: 24

Бренд: Bryant Страницы: 4

Бренд: Toyostove Страницы: 17

Бренд: WMT Страницы: 7

Marvair AVPA 24

Бренд: Airxcel Страницы: 44

Бренд: Daikin Страницы: 316

Бренд: Magic-Pak Страницы: 18

GOULDS e-SVI Series

Бренд: Xylem Страницы: 40

Gyre 300 Series

Бренд: Maxspect Страницы: 164

Бренд: T.I.P. Страницы: 120

Бренд: EBARA Страницы: 28

TV 301 Navigator 969-8918

Бренд: Varian Страницы: 55

Home FKIR 350 WIFI

Бренд: Somogyi Elektronic Страницы: 24

GUARDIAN Smart Sense AD250

Бренд: L.B. White Страницы: 24

Бренд: MILL Страницы: 10

Бренд: salmson Страницы: 24

Бренд: NARVI Страницы: 40

Бренд: Sulzer Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды