Toshiba Estia RUA-CP1701H Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 164

background image

Monobloc Outdoor Unit Service Manual

5

1. Safety precautions

The unit and this service guide list very important safety precautions. Understand the following details (indications and
symbols) before reading the body text, and follow the instructions.

[About indication]

Indication

Meaning of indication

⚠

DANGER

Indicates that a wrong operation may cause a service engineer and the third persons around to
get fatal or serious injuries.

⚠

WARNING

Indicates that a wrong operation may cause a service engineer and the third persons around to
get fatal or serious injuries, or that unit defective after the operation may cause a user to have a
similar serious accident.

⚠

CAUTION

Indicates that a wrong operation may cause a service engineer and the third persons around to
get injuries or may cause property damage*, or that unit defective after the operation may cause
a user to have a similar accident.

* Property damage indicates extended damage to property, furniture, livestock, or pets.

[About symbols]

Symbol

Meaning of symbol

Indicates a forbidden action.
Specific forbidden actions are described in text near the symbol.

Indicates a forcible (must do) action.
Specific forcible actions are described in text near the symbol.

Indicates a caution (including danger and warning).
Specific cautions are described in picture or text inside or near the symbol.

⚠

DANGER

<Turn off the power breaker>
Turn off the power breaker before removing the front panel and cabinet.

• Failure to do so may cause a high voltage electric shock, leading to death or injury.
• During an operation, the second side circuit of high pressure transmission(*) are applied with a high voltage of 230 V
or higher.
• Touching the circuit even with an electrical insulator, let alone a bare hand or body, causes an electric shock.

∗

: For details, see the schematic.

<Discharge between terminals>
When the front panel and cabinet are removed, make short-circuit current to discharge between high pressure
capacitor terminals.

• Failure to do so may cause a high voltage electric shock, leading to death or injury.
• After the power is turned off, the high pressure capacitor is still charged with high voltage.

<Forbidden>
Do not turn on the power breaker after removing the front panel cabinet.

• Failure to do so may cause a high voltage electric shock, leading to death or injury.

⚠

WARNING

<No modification>
Do not modify the unit.

• Do not disassemble or modify the parts also.
• A fire, an electric shock, or an injury may occur.

<Use specified parts>
Use the specified parts (

∗

) when replacing them.

• Using parts other than specified ones may cause a fire or an electric shock.

∗

: For details, see the parts list.

<Keep children away from unit>
Keep any person (including children) other than service engineers away from a failure diagnosis or repairing
place.

• A tool or disassembled parts may cause an injury.
• Advise the customer to keep the third persons (including children) away from the unit.

«
...
4
5
6
7
8
...
»

Содержание Estia RUA-CP1701H





































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Estia RUA-CP1701H

Бренд: York Страницы: 16

Бренд: TapFlo Страницы: 35

Бренд: Rainman Страницы: 17

Бренд: Fahrenheat Страницы: 6

Бренд: veito Страницы: 24

Бренд: Vasco Страницы: 32

Alterma EDHQ011AA6V3

Бренд: Daikin Страницы: 22

Бренд: Essentielb Страницы: 29

GUARDIAN Smart Sense AD250

Бренд: L.B. White Страницы: 24

Бренд: MILL Страницы: 10

Бренд: Warm Tech Страницы: 61

Бренд: Wilo Страницы: 16

Бренд: SAMES KREMLIN Страницы: 49

SKS 1000 Series

Бренд: Pentair Jung Pumpen Страницы: 12

Бренд: Samoa Страницы: 38

Бренд: Solinst Страницы: 2

Бренд: IDM-Energiesysteme Страницы: 44

Бренд: Quadro Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды