Toshiba Estia RUA-CP1701H Скачать руководство пользователя страница 60

Страница: 60 / 164

Monobloc Outdoor Unit Service Manual

Override

Conditions

Action

Minimum OAT in Cooling

Cool Mode and TO2 [P039] is below
“oat_minc” parameter ([P516], default
is 0°C) for 15 min.

Do not allow the start. Stop unit if
already running.

Minimum EWT in Cooling

EWT is strictly below 6°C + offset.
With offset increased of 2K each time
alarm #50 or #51 occurs.

Do not allow the start

Low OAT in Cooling

Units Heat pump17 and Heat pump21,
Cool Mode and TO2 [P039] is (strictly)
below 15°C.

Increase minimum compressor
frequency to 35 Hz (17 kW) or 50 Hz
(21 kW)

OAT above 26°C in Cooling

Units 17 and 21 kW, Cool Mode and
TO2 [P039] is above 26°C.

Increase minimum compressor
frequency to 25 Hz (17 kW) or 36 Hz
(21 kW)

OAT above 40°C in Cooling

Units 17 and 21 kW, Cool Mode and
TO2 [P039] is above 40°C.

Reduce compressor frequency
range between 45 and 70 Hz.

Low SST avoidance

Units Heat pump17 and Heat pump21,

Cool Mode, TO2 ≤ 26°C and LWT ≤
9°C.

Increase minimum compressor
frequency to 45 Hz (Heat pump17)
or 50 Hz (Heat pump21)

Water Exchanger Freeze
Protection in Cooling

Cool Mode and SST is below 0°C.

Freeze compressor request
frequency

Negative OAT in Cooling

Chiller units, Cool Mode and TO2 <
0°C.

Increase minimum compressor
frequency (63 Hz for Chiller17 and
77.4 Hz for Chiller21). A 0.1Hz/s
ramp is applied.

Water Flow Failure

Water is not flowing through the water
exchanger.

Stop compressor

Compressor stopped by the
Inverter

Compressor was running for at least 3
minutes and Inverter stop it.

Stop compressor control if override
is active for more than one minute

Booster Heating

Booster Heating Mode selected.

Run compressor at the
maximum frequency in Heat
Mode

Booster Cooling

Booster Cooling Mode selected.

Run compressor at the maximum
frequency in Cool Mode

100

System Alarm

Alarm relative to the unit or the system Compressor is stopped immediately or

is not allowed
to start

101

Compressor or
Inverter Alarm

Alarm relative to the Inverter or the
compressor

Compressor is stopped
immediately or is not allowed to start

102

Configuration
Error (Factory)

No or wrong configuration

Compressor is not allowed to start

201

Rating Cool

QCK_TEST enabled,
RAT_MODE = 1 and
RAT_FREQ = desired freq

Run compressor at the
requested frequency in Cool
Mode for test purpose

202

Rating Heat

QCK_TEST enabled,
RAT_MODE = 2 and
RAT_FREQ = desired freq

Run compressor at the requested
frequency in Heat
Mode for test purpose

203

Ramp Cool Mode

QCK_TEST enabled,
RAT_MODE = 3 and
RAT_FREQ = rate (Hz/min)

Run compressor by ramping up or
down the frequency in Cool Mode for
test purpose

204

Ramp Heat Mode

QCK_TEST enabled,
RAT_MODE = 4 and
RAT_FREQ = rate (Hz/min)

Run compressor by ramping up or
down the frequency in Heat Mode for
test purpose

Содержание Estia RUA-CP1701H





































































































































































Результаты поиска

Содержание Estia RUA-CP1701H

Отзывы:

Похожие инструкции для Estia RUA-CP1701H

Бренды по названию

Популярные бренды

Toshiba Estia RUA-CP1701H, Руководство по обслуживанию

Результаты поиска

Содержание Estia RUA-CP1701H

Отзывы:

Похожие инструкции для Estia RUA-CP1701H

Бренды по названию

Популярные бренды