Suzuki 2000 Grand Vitara SQ416, Руководство по обслуживанию

Страница: 551 / 729

YH4
GRAND
VITARA
6E1-14 ENGINE AND EMISSION CONTROL SYSTEM (G16 / J20 ENGINES)
16 Heater blower switch
17 A / C signal (if equipped)
18 ——
19 “4WD” lamp (4WD)
20 “O / D OFF” lamp (A / T)
21 “POWER” lamp (A / T)
22 A / C fan motor relay (if equipped)
23 Fuel pump relay
Ground for HO2S–2
Ground for CO adjusting resistor
28 Ground
29 Ground for DLC
30 Ground for CKP sensor shield wire
9 Throttle position (TP) sensor
10 Mass air flow (MAF) sensor
TERMINAL
CIRCUIT
TERMINAL
CIRCUIT
TERMINAL
CIRCUIT
1
Power source for CO adjusting
resistor
2 Power source for back up
3 Heater of HO2S-2 (if equipped)
4 ——
5 Duty output terminal (if equipped)
6 Tachometer
7 MIL
8 A / C cut signal (if equipped)
9 Main relay
10 CO adjusting resistor (if equipped)
31
Power / Normal change switch
(A / T)
32 Lighting switch
33 O / D cut switch (A / T)
34
Stop lamp switch
(Brake pedal switch)
35 ——
1 Intake air temp. sensor
2 Engine coolant temp. sensor
Knock sensor (J20)
E61
8
Manifold absolute pressure (MAP)
sensor
C51-3
20 Ignition switch
21 Ground for TP sensor
22 Ground for HO2S-1
23 ——
24 ——
15
Transmission range switch “D”
(A / T)
16
Transmission range switch “N”
(A / T)
17
Transmission range switch “R”
(A / T)
18
Transmission range switch “P”
(A / T)
19 ——
20
Shield wire ground for A / T output
speed sensor
21
Shield wire ground for A / T input
speed sensor
22 A / T output speed sensor (–)
23 A / T output speed sensor (+)
24-25 ——
26 4WD low switch
27
Transmission range switch “L”
(A / T)
28
Transmission range switch “2”
(A / T)
C51-1
C51-3
22
Ignition coil assembly for
No. 3 (J20)
23
24
Ignition coil assembly for
No.2 and No.3 spark plugs (G16)
Ignition coil assembly for
No.2 (J20)
Ignition coil assembly for
No.1 and No.4 spark plugs (G16)
Ignition coil assembly for
No.1 (J20)
25 Vehicle speed sensor
26 CMP sensor (+)
27
Pressure switch in 4WD air
pump assembly (if equipped)
C51-2
21
Ignition coil assembly for
No.4 (J20)
27 ——
28 Fuel level sensor
24
Heated oxygen sensor-2
(if equipped)
8 Fuel injector No.4
9 Fuel injector No.3
10 IAC valve (stepper motor coil 4)
11 IAC valve (stepper motor coil 3)
12 IAC valve (stepper motor coil 2)
13 EGR valve (stepper motor coil 4)
14 EGR valve (stepper motor coil 3)
15 EGR valve (stepper motor coil 2)
16 EGR valve (stepper motor coil 1)
17 EVAP canister purge valve
18 4WD switch (if equipped)
19 CKP sensor (+)
20 CKP sensor (–)
1 Fuel injector No.2
2 Fuel injector No.1
3 IAC valve (stepper motor coil 1)
4 Heater of HO2S-1
5 ——
6 ——
7
4WD air pump assembly
(if equipped)
TERMINAL ARRANGEMENT OF ECM (PCM) CONNECTOR (VIEWED FROM HARNESS SIDE)
11-12 ——
13 Data link connector
14 Test switch terminal (if equipped)
15 Rear defogger switch (if equipped)
25 ——
26
30 ABS control module (if equipped)
29
Diagnosis switch terminal
(if equipped)
5 Ground for MAF sensor
6 Ground
7 Power steering pressure switch
Ignition timing adjusting resistor
(G16, if equipped)
3
4 Power source
12 Ground for HO2S-1 shield wire
13 Power source for TP sensor
14 Power source for MAP sensor
15 Power source
16 ——
17 Ground
18 Engine start signal
19 ——
Heated oxygen sensor-1
(if equipped)
11
26 Ground for CMP sensor
1 Shift solenoid-B (A / T)
2 Shift solenoid-A (A / T)
3–7 ——
8 TCC solenoid (A / T)
9 ——–
10 A / T input speed sensor (–)
11 A / T input speed sensor (+)
12-14 ——
Ground for IAT sensor, ECT sensor
MAP sensor and / or Ignition timing
adjusting resistor
25
C51-1