YH4
GRAND
VITARA
6A2-56
ENGINE MECHANICAL (H25 ENGINE)
10) Install 1st timing chain.
Refer to item “1ST TIMING CHAIN AND CHAIN TENSIONER”
in this section for installation.
11) Install LH bank 2nd timing chain.
Refer to item “LH (NO.1) BANK 2ND TIMING CHAIN AND
CHAIN TENSIONER” in this section for installation.
12) Install timing chain cover.
Refer to item “TIMING CHAIN COVER” in this section for instal-
lation.
13) Install oil pan, front differential housing, P/S system, cooling
system, intake manifold with throttle body and other parts.
14) Install CMP sensor. Refer to Section 6F2 for details.
15) Refill cooling system with coolant, front differential with gear oil,
P/S system with specified fluid and engine with engine oil.
16) Check wheel alignment referring to Section 3.
17) Verify that there is no fuel leakage, water leakage and oil leak-
age at each connection.
18) Check ignition timing, referring to Section 6F2.
CAUTION:
Don’t turn camshafts or start engine (i.e., valves
should not be operated) for about half an hour after re-
installing hydraulic valve lash adjusters and cam-
shafts. As it takes time for valves to settle in place, op-
erating engine within half an hour after their installa-
tion may cause interference to occur between valves
themselves or valves and piston.
If air is trapped in valve lash adjuster, valve may make
tapping sound when engine is operated after valve
lash adjuster is installed. In such a case, run engine
for about half an hour at about 2,000 – 3,000 r / min.,
and then air will be purged and tapping sound will
cease. Should tapping sound not cease, it is possible
that valve lash adjuster is defective. Replace it if de-
fective.
If defective adjuster can’t be located by hearing
among 24 of them, check as follows.
1) Stop engine and remove cylinder head cover.
2) Push adjuster downward by hand (with less than 20
kg or 44 lbs force) when cam crest is not on adjuster
to be checked and check if clearance exists be-
tween cam and adjuster. If it does, adjuster is defec-
tive and needs replacement.
Содержание 2000 Grand Vitara SQ416
