Eaton LMS Скачать руководство пользователя страница 91

Страница: 91 / 202

L a m i n a t e H o o k - o n
S h e l v e s

Shelf Width

Number of

Brackets

Load Capacity

24” -42”Shelves

610mm-1067mm

300 lbs

136 kg

48”-60” Shelves

1219mm-1524mm

300 lbs

227 kg

72” Shelves

1828mm

300 lbs

342 kg

Maximun Shelf Loading

BASICP-4

technical furniture

1. Determine the location of the

Shelf

. Position the

Shelf Supports as shown in

Figure 1

. Insert the hooks

on the back of the supports into the trapeziod shaped
slots in the upright posts and push down.

2. To assure the hooks are seated, tap the top rear
corner with a plastic mallet or equivalent.

3. Align the pre-drilled holes in the bottom surface of
the shelf with the holes in the left hand and right
hand shelf supports. See

Figure 2

4. Fasten the shelf to the left /right hand shelf supports
using the four #10AB x 5/8” long phillips head screws
provided. See

Figure 2

5. Lock the shelf supports in position with the #10-24 x
3/8” long phillips head screws provided. See

Figure 3

Tools required

-Plastic mallet

Laminate Shelf

Figure 1

Upright Post

Basic Plus

R.H. Shelf support

L.H. Shelf support

Slots

Shelf

Shelf support
(L.H. shown)

Pre-drilled hole

#10AB x 5/8” phillips
head screw

Figure 2

Shelf

Shelf support

#10-24 x 3/8” phillips
head screw

Basic plus

H-3

Содержание LMS











































































































































































































Результаты поиска

Содержание LMS

Отзывы:

Eaton LMS, Руководство по установке, Страница: 91 / 202

Результаты поиска

Содержание LMS

Отзывы: