Eaton LMS Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 202

Eaton LMS Скачать руководство пользователя страница 5

-1-

F u l l   F r a m e   a n d
U p r i g h t   A s s e m b l y
( c o n t . )

UPRIGHT ASSEMBLY

A-2

82354

Cover

Upright

Top cap

Figure 3

Make sure the frame is attached to the upright as
shown in

Figure 4.

It will now stand by its self.

Install the remaining screws. Tighten each side
after all the screws have been installed.

3. Adjust the Foot Levelers with the leveling wrench
until the unit(s) are square and level. For 48” wide

and larger frames, lower the levelers under the
   intermediate posts until they touch the floor.

4. Install the

Top Caps

and

Cable Management

Covers

. Also install the

Hole Plugs

on the out-

side of each Upright.

If you are installing

Tech Wall Panels

, please

refer to page 1 Section G for installation.
instructions.

NOTE

: There are

three

kinds of

Uprights

. All include

Vertical Cable Management. See

Figure 2

. All are shipped

fully assembled. It is recommended to slide the

Cover

from

the top of the Vertical Cable Management Duct prior to
assembly of the Upright to its frame. Remove the protective
inner packing located inside the vertical duct.

1. Assign uprights to be

left end

and

right end

relative to a frame.

NOTE

: If a

Tech Corner Post

will be used, refer to page A-9

for additional assembly instructions.

2.With two people, stand the

Full Frame

up in the

approximate area it will be used. Attach the appro-
priate Upright (left, right and intermediate) to each
end with two 1/4”-20 x 5/8” screws.

Do not tighten

at this time

.

Vertical cable
management cover

Figure 4

Top cap

Frame

Upright

1/4”-20 x 1-5/8”
Button head cap screws

Foot levelers

Top view

Foot levelers

Full

Plastic hole
plug

Figure 2

Full Depth Upright

Enhanced Upright

Double Upright

technical furniture

«
...
3
4
5
6
7
...
»

Содержание LMS











































































































































































































Отзывы:

Нет отзывов