manualshive.com logo in svg

Eaton LMS, Руководство по установке, Страница: 71 / 202

Поделиться
Скачать
Eaton LMS Скачать руководство пользователя страница 71

-1- 

Tools Required 

      -Phillips head screwdriver 
      -Plastic mallet 
      -5/33” Allen wrench 
 
1. Determine the location of the 

Shelf End Panels

.  

    Positon the end panels as shown. (The End Panels  
    are stamped “R.H.” and “L.H.”) Insert the hooks on  
    the End Panels into the slotted standards and push  
    down. To assure the hooks are seated, tap the top  
    rear corner of the panels with a plastic mallet or  
    equivalent.  See 

Figure 1

. 

 
    Make sure both End Panels are in the same location. 
 

NOTE

:  If the shelf is being installed in the lowest   

               possible position, it is recommended  that the  
               shelf be pre-assembed as shown above (upper  
               right), and then installed on the Full Frame 
               with two people.  This allows the screws to  
               be pre-tightened.  
 
2. The End Panels accept single or multiple levels of  
    steel shelves. Refer to shelf position diagrams on 
    next page. 
 
    Install the #10-24 x 1/2” Phillips head machine     
    screws in each End Panel, leaving approximately 1/8”   
    of thread exposed.  See 

Figure 1

. 

 
3. With two people, carefully position the steel shelf  
    over the screws.  Note: install the shelf with the 1/16”  
    corner notch toward the back.  Drop the shelf in  place 
    and tighten the screws.  

   

Maximum Shelf Loading 

   The recommended maximum loading for most shelf   
   components is 300lbs regardless of shelf width. If more than   
   one shelf is installed on a pair of end panels, the maximum  
   load per pair of end panels is not to exceed 300 lbs.  
  
   

Heavy Duty Shelf Supports 

(#8161X) can be purchased  

   separately to increase the weight capacity of the shelf.  
   See page G-9 for details. 

Steel Hook-On Shelving 

Full frame 

1.00 spaces 

R.H. End 

#10-24 x 1/2” Phillips 
head screw 

Slotted  
standard 

Figure 1 

1/8”  

Shelf 

Screw 

End panel 

LB25 

H o o k - o n   S h e l v i n g    
C o m p o n e n t s  

 
 

  

technical furniture 

Upper Shelf 

Tower Shelf 

Electronics Shelf 

General Purpose 
Shelf 

Mini Electronics/Telephone 
Shelf 

F-1 

Содержание LMS











































































































































































































Отзывы:

Нет отзывов