manualshive.com logo in svg

Eaton LMS, Руководство по установке, Страница: 123 / 202

Поделиться
Скачать
Eaton LMS Скачать руководство пользователя страница 123

R a c k   M o u n t   S h e l f  
 

 

Tools Required 

      -11/32” Combination wrench 
      -3/8” Combination wrench 
      -Flat blade screwdriver 
      -Phillips head screwdriver 
      -Tape measure 
  

NOTE

: These instructions cover installation of the 

Stationary Shelf

, and 

              

Roll-out Shelf

. 

               

    CLIP NUT INSTALLATION  
  

    

Clip Nuts

 (included with Rack Module) provide 

    mounting points on 19” and 24” rack mount equip- 
    ment rails.  
     
    Clip Nuts have a front or screw side. Consider which 
    way it should face for ease of access to the screw  
    head during component installation. See 

Figure 1

. 

   
    To remove a Clip Nut from a rail, insert a flat blade  
    screwdriver or knife under the tab on the front and 
    pry up, freeing the retaining ring from the rail. See 
    

Figure 1

. 

  
1. Select the location at which the shelf or roll-out will be  
    installed in the Rack Mount Module. 
     
    

NOTE

: If the component is a roll-out and the weight  

    load exceeds 75lbs. or more, use four screws in each of  
    the brackets. See 

Figure 4

. It will be necessary to select   

    a four hole grouping that matches the bracket.The center  
    two holes will be .50” apart. If less than 75 lbs., two  
    screws are sufficient. 
  
2. Snap one Clip Nut into the top hole at the selected 
    position. For light loads, place the second Clip Nut four 
    holes (1.75”) below. Start #10-32 x 1/2” screws. 
  
    Use a mounting bracket as a guide to match holes and  
    attach corresponding Clip nuts. 

Do not 

start the screws. 

  
3. Measure from the bottom of the Vertical Rail to the top 
    Clip Nut. Assemble Clip Nuts onto the three other rails 
    at the measured height. 
 
                   
 

Rack Mount Roll-Out Shelf 

Figure 1 

Rail 

Clip nut 

Clip nut 

#10-32 x 1/2” Pan 
head machine screw 

Clip nut 

Front or screw side 

82158 

 
 

  

technical furniture 

K-20 

Содержание LMS











































































































































































































Отзывы:

Нет отзывов