manualshive.com logo in svg

Eaton LMS, Руководство по установке, Страница: 120 / 202

Поделиться
Скачать
Eaton LMS Скачать руководство пользователя страница 120

R a c k   M o u n t    
R e a r   S e r v i c e   D o o r s  

NOTE

: 

Rear Service Doors 

are available in five heights (24”, 38”, 61”, 72”, and 84”) and in the two Full Frame Module 

              widths (24” and 30”). The Doors are designed to attach to the rear of the “Full Frame”. All Doors have left hand  
              mounted “lift-off” hinges which allow the removal of the Door Panel for total service access. The Frame of the 
              Rear Service Door has openings for the passage of cables into the Full Frame Cable Management channels or 
              into an adjacent Rear Service Door. 
 

Tools Required

: 

     -Plastic mallet 
     -Phillips head screwdriver 
 

 

DOOR INSTALLATION

 

  
1. Carefully remove the LAN Locker Rear Service  
    Door assembly from its packaging. Lay the assembly 
    face down on a protective surface. 
  
    For shipping purposes, the 

Door Panel

 is secured to 

    the 

Door Frame

 with two #10 Phillips head screws. 

    The screws are located on the Latch side of the Door, 
    one near the top and one near the bottom. Remove  
    and discard the two screws. See 

Figure 1

. 

  
2. 

For the  three tallest Rear Service Doors (84”, 72”, 

    and 61” high) it is recommended that the Door Pan- 
    el be removed from the Frame before further assem- 
    bly. This will reduce the total weight of the unit and 
    make it easier to assemble to the Full Frame Slotted 
    Uprights. The Door Panel may be left attached to the 
    smaller 34” and 24” high units. 
  
    

To remove the Door Panel, first carefully turn the en- 

    tire Door assembly over so that it lays on its back.  
    Depress the 

Latch 

release button and open the Door  

    approximately 90 degrees. To disengage the Door  
    hinges, carefully slide the Door towards the top of  
    the Frame. The hinges will slip apart so that the Door  
    may be set aside. See 

Figure 2

.   

  

 3. The three tallest Rear Service Doors, 84”, 72”, and 
     61” are designed to attach to corresponding Full 
     Frame heights and will cover the entire height of 
     the Frame when installed. 

83203 

Figure 2 

Door panel 

Door hinge 

Latch detail 

Latch release 
button 

Slide to disengage hinges 

Door frame 

Latch 

 
 

  

technical furniture 

K-17 

              Figure 1 

Rear Service Door Assembly

 

#10 Phillips head 
screws 

Door panel 

Door frame 

Содержание LMS











































































































































































































Отзывы:

Нет отзывов