Eaton LMS Скачать руководство пользователя страница 150

Страница: 150 / 202

Tools Required

-Phillips Head Screw Driver
-Plastic mallet

ATTACHING TO LMS BASIC

PLUS (BACK OF

UPRIGHT)

1. The rear of the

Upright

Post

has a recessed area with

a row of small holes. Align the holes in the

Mounting

Channel

with the Post holes and attach with the #8

screws.

Starting at the top

, snap the

Cable Manage-

ment Duct

into the channel.

NOTE

: It is meant to be a

tight fit, so use of a mallet and block to tap the duct in
place may be necessary. Once started, continue taping
it in, moving down a few inches at a time. Next, install
the

Cover(s)

. See

Figure 1

ATTACHING AN INNER CABLE MANAGEMENT DUCT

1. The inside of the

Upright

Post

has two rows of small

holes, one row on either side of the upright seam.
Position the

Mounting Channel

as shown in

Figure

. Screw the Mounting Channel to the Upright Post

using the #8 screws every other hole on each side.
Follow the above instructions for inserting the Cable
Management Duct into the Channel.

B a s i c P l u s
C a b l e M a n a g e m e n t

Figure 2

BASICP3

Figure 1

Upright post

Cable management
duct

Mounting channel

Cover(s)

#8 Screws

Upright post

Cover(s)

#8 Screws

Cable management
duct

technical furniture

M-15

Содержание LMS











































































































































































































Результаты поиска

Содержание LMS

Отзывы:

Eaton LMS, Руководство по установке, Страница: 150 / 202

Результаты поиска

Содержание LMS

Отзывы: