manualshive.com logo in svg

Eaton LMS, Руководство по установке, Страница: 63 / 202

Поделиться
Скачать
Eaton LMS Скачать руководство пользователя страница 63

-1- 

 

Tools Required 

      -Tape Measure 
      -Electric Drill 
      -9/32”(.281) Drill 
      -Phillips head Screwdriver 
 
1.  Accurately measure, locate and drill the correct   
     number of .281 diameter holes in the back of the  
     Worksurface.  See 

Figure 1

 and the chart below  

     for the specific hole quantities and location. 
 
 

“B” 

“C” Spaces @ “D”= “E” 

“A” 

Worksurface 

Figure 1 

Backstop 

2.  Install the 

Backstop 

onto the Worksurface 

     using the #10AB x 1-3/4” phillips pan head    
     thread forming screws provided.  See   
     

Figure 2

. 

 

Note

:

 

If the Backstop is being installed onto a  

          Worksurface that was produced prior to  
          October 1995, the Backstop may extend  
          over the back edge of the Cable 
Manage- 
          ment bushing(s). 
 
 
 
 

Figure 2 

W o r k s u r f a c e  
B a c k s t o p  

Hole Locations 

 

83502 

 
 

  

technical furniture 

81489 

D-16 

Backstop 

#10AB x 1-3/4” phillips 
pan head thread forming 
screws 

Worksurface 

Cable management 
bushing 

Содержание LMS











































































































































































































Отзывы:

Нет отзывов