Eaton LMS Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 202

Eaton LMS Скачать руководство пользователя страница 4

-1-

F u l l F r a m e a n d
U p r i g h t A s s e m b l y

A-1

81489

Tools Required

-Tape measure
-Phillips head screwdriver
-5/32” Allen wrench (provided)
-1/4” Allen wrench (provided)
-Plastic mallet
-1/2” Wrench
-2 ft. to 3 ft. level
- Leveling wrench (provided)

NOTE

: 24”, 30”, 36”, 42”, and 48” wide

Full Frames

are one-piece units, ready for assembly to the Uprights.
60”, 72”, and 90” wide units are two-piece construction
and 96” wide Frames ship as three pieces. All require
assembly before before attachment to the Uprights. See
page A-2.

1. 60”, 72”, and 90” Frames have a left and right half.
A warning label is on the rear of the left half. See

Figure 1

. The 96” frame has a left, a right, and a “I”

shaped center section. Lay the sections on the floor,
butting the ends of the top and bottom channels.

Important!

Compare the trapazoidal holes (holes to

accept components) of the Frame sections making sure
they are in the same direction.

2. Remove the 5/16”-18 x 1.00 Cap screws and washers
from the top and bottom channels. The screws and
washers are shipped in place to prevent damage to
the threads.

technical furniture

Cap

Full Frame R.H.

“I” shaped center
section (96” frame)

Warning label

Full Frame L.H.

#10-24 x 3/8”
Screw

Support tube,
bottom

5/16”-18 x 1.00”
Cap screw

Adjustable leveler

Figure 1

Lock washer

Bottom channel

Top channel

Support tube,
top

4. Bolt the tubes in place with the 5/16”-18 x 1.00 Cap
screws and washers just removed. Repeat the proccess
for the bottom. See

Figure 1

. Tighten all screws.

3. Packaged with the Full Frame are two full length

Support Tubes

that bolt into the top and bottom

channels. These tubes tie the two halves together.
See

Figure 1. Note

: The bottom tube has adjustable

Levelers

. Drive a #10-24 x 3/8” screw through the

channel into the pre-drilled hole in the support tube on
both sides of the joint, both top and bottom.

NOTE

: The

60” Frame only has holes on one side of the joint. See

Figure 1

.

5. Place the

Cap

over the Top Support Tube to

verify its fit. Next, remove the protective paper from
the adhesive strip on its underside and secure it to the
top of the Frame. See

Figure 1.

«
...
2
3
4
5
6
...
»

Содержание LMS











































































































































































































Отзывы:

Нет отзывов