manualshive.com logo in svg

Eaton LMS, Руководство по установке, Страница: 170 / 202

Поделиться
Скачать
Eaton LMS Скачать руководство пользователя страница 170

K e y b o a r d  
A c c e s s o r i e s  

Tools Required 

      - Phillips head screw driver 

MOUNTING TO UNDERSIDE OF WORKSURFACE 

1. Align the 

Track

 mounting holes to pre-drilled holes  

    on the underside of the worksurface. See 

Figure 1

. 

  
2. Install four screws along each side of the Track and 
    a rear center screw with a 

Bumper

. Make sure screws 

    are drawn down tight enough to ensure proper clear- 
    ance between the 

Articulating Arm Mechanism 

and    

    the track. 
  
3. Mount the 

Keyboard Platform

 to the tray brackets 

    of the Articulating Arm Mechanism. Install six screws 
    into the pre-drilled holes in the underside of the 
    Platform. 
  
4. Loosen the knob and lower the mechanism to the 
    down position. Re-tighten the knob. 
  

  
5. Slide the mechanism into the grooves on the Track 
    until it contacts the Rear Bumper. 
  
6. Install the 

Front Bumper

 and screw. 

  
7. Apply the 

Warning Label

 as shown. 

  
8. 

Cord Clips

 are provided for wire management. 

  
NOTE: For smooth sliding operation, it may be  
             necessary to apply a light layer of lubrication 
             to both sides of the Track. Slide the mechan- 
             ism back and forth to spread the lubrication. 
  
* Keyboard mechanism intended for keyboard  
   weights only. 

NOTE

: For non-standard application, use the Track 

              as a drill template. Keeping the Track per- 
              pendicular to both edges, position it 1/2” 
              from the front edge of the worksurface. Drill  
              (10) .109 dia. holes. 

Figure 1 

Keyboard platform 

Articulating arm 
mechanism 

Tray brackets 

Handle (tilt adjustment) 

Pre-drilled holes 

Worksurface 

Track 

Bumper 

#8 x 1/2” Phillips head 
screws 

Knob (up & down adjustment) 

* Label 

#10 x 3/4” Phillips head 
screws 

#10 x 3/4” Phillips head 
screws 

 

Bumper 

69871 

 
 

  

technical furniture 

O-1 

Содержание LMS











































































































































































































Отзывы:

Нет отзывов