manualshive.com logo in svg

Eaton LMS, Руководство по установке, Страница: 86 / 202

Поделиться
Скачать
Eaton LMS Скачать руководство пользователя страница 86

L o c k i n g  
C o m p a r t m e n t  

Tools Required 

     -Phillips head screwdriver 
     -Plastic mallet 
  
 
 

NOTE

: Some assembly may require assistance.  

 
 

REAR AND END PANEL INSTALLATION

 

  
1. Install the 

Rear Panel

 by inserting the hooks on either 

    side of the panel into the Slotted Standards of the Full 
    Frame and pushing down. To assure that the hooks are 
    seated, tap the top corners with a plastic mallet or  
    equivalent. See 

Figure 1

.  

  
2. Position the 

End Panels 

as shown in 

Figure 2

. Insert   

    the hooks on the End Panels into the Slotted Standards 
    and push down. Tap the top corners of the panels with 
    a plastic mallet to assure that the hooks are seated. 
  

SHELF INSTALLATION 
  

1. There are three factory installed screws along the top  
    and bottom edge of each Side Panel. These screws must  
    be backed out approximately 1/8”(3mm) as shown in 
    

Figure 3

 (inset).  

  
2. After backing out all six lower screws, position the 

Shelf

 

    between the End Panels above the screws. Lower the  
    Shelf so that all six screws engage their corresponding 
    slots in the Shelf. Next, tighten the screws to secure the 
    Shelf. See 

Figure 3

. 

  
 

Locking Compartment 

Figure 1 

Rear panel 

Hook 

Slotted standard 

Full frame 

Figure 3 

Figure 2 

Full frame 

Hooks 

Slotted standard 

End Panel 
(R.H. shown) 

Screws 

80172 

 
 

  

technical furniture 

G-1 

Screw 

End Panel 

Shelf 

1/8” 

End Panel 

Shelf 

Содержание LMS











































































































































































































Отзывы:

Нет отзывов