manualshive.com logo in svg

Eaton LMS, Руководство по установке, Страница: 67 / 202

Поделиться
Скачать
Eaton LMS Скачать руководство пользователя страница 67

-1- 

Tools Required

 

      -Phillips head screwdriver 
      -5/32 Allen wrench 
 

Note:

 The 

Tower Roll-Out

 can be connected to the Full 

Frame, Open Frame, Basic, or Basic Plus prior to use to 
prevent forward creep during repeated use. 
 
The recommended maximum load capacity of the Tower 
Roll-Out is 1000 lbs, 200 lbs on the 12” wide unit. 
 

Assembling the handle to the Tower Roll-Out 

 
1.  Place the Roll-Out , upside down, on it’s shipping  
     carton.  Extend the Roll-Out front approx. 2”-3”  
     beyond the carton edge.  See 

Figure 1

.  Remove  

     the tape strips that held the 

Base Pan 

in position  

     during shipping, and slide the Base Pan back. 
 

Note

: The 12” Roll-Out has a smaller handle (6.00”)      

            than the 24” through 72” (12.76”).  
 
2.  Assemble a 

12.76” Handle

 to the Roll-Out using  

     the two lockwashers and  4mm x 6mm phillips fillister  
     head machine screws. Tighten securely. See 

Figure 1

. 

      
 
 
 

Tower Roll-Out 

Figure 1 

Tower roll-
out 

Carton 

Base pan 

Lock washer 

4mm x 6mm phillips 
fillister head screws 

Handle 

 

81866 

T o w e r   R o l l - o u t  
S h e l f      

 
 

  

technical furniture 

E-3 

Содержание LMS











































































































































































































Отзывы:

Нет отзывов