manualshive.com logo in svg

Eaton LMS, Руководство по установке, Страница: 68 / 202

Поделиться
Скачать
Eaton LMS Скачать руководство пользователя страница 68

-2- 

2. Position the Tower Roll-out component between the  
    feet of the unit. Center it between the feet and  
    extend the Roll-Out platform from the Base Pan.  See  
    

Figure 2

. 

 

Note

: If using multiple 12” Tower Roll-Outs, space them   

           evenly between the feet.  Six Roll-Outs used with  
           a 72” wide Full frame will have approximately  
           5/16” between each.  The spacing will vary de- 
           pending on the Full Frame width. 
 

Installing the Retention Brackets (Full Frame, Lower 
Frame, Open Frame) 

 
3. Install 

Bracket “A “

or 

“B”

 (use Bracket “A” for Full 

    Frame or Open Frame; use Bracket “B” for Lower   
    Frame) by inserting the side without holes under the  
    Frame. It may be necessary to raise the frame slightly 
    in order to slide the Bracket underneath. See 

Figure 2

. 

 

Note

: The center 12” Roll-Out (using 5 Roll-Outs) on a   

           60” wide Full Frame cannot be attached to the   
           Frame due to the location of the double standard   
           and adjustable glide in the center. 
 
4. Slide the Bracket over the back flange on the Base Pan  
    and align the holes in each.  See 

Figure 2

. 

 
    Fasten the Brackets in place using the #10-24 screws  
    provided. 
 
    Two Brackets are on each 24” through 72” Tower roll- 
    out. One with each 12” Tower roll out. 
  

Note

: Additional holes are provided in the Base Pan 

           of the 24” thru 72” wide Tower Roll-Outs to 
           facilitate installing units in a back-to-back  
           configuration on LMS Frames with double up- 
           rights. 

Full frame 

Bracket “A” 
       or 
Bracket “B” 

Full frame 

Foot 

Foot 

Base pan 

Tower roll-out 
platform 

#10-24 x .37 
Phillips head screws 

Figure 2 

 

1.28” 

2.62” 

         Bracket “A” 
Full Frame/Open Frame 

  Bracket “B” 
Lower Frame 

 

81866 

T o w e r   R o l l - o u t  
S h e l f   ( c o n t . )      

 
 

  

technical furniture 

E-4 

        Bracket “C” 
        Foundations 

Содержание LMS











































































































































































































Отзывы:

Нет отзывов