manualshive.com logo in svg

Eaton LMS, Руководство по установке, Страница: 52 / 202

Поделиться
Скачать
Eaton LMS Скачать руководство пользователя страница 52

C o r n e r   H o o k - O n  
W o r k s u r f a c e  

Tools Required 

     -5/32” Allen Wrench (provided) 
     -Phillips head screwdriver 
     -Plastic mallet 
  

Important

 

Corner Hook-on Worksurfaces

 with 36” deep sides 

require the use of: 
        -40” deep 

Uprights 

(6L08, 7L08, 8L08) 

        -

Aluminum Top Supports

 (MA01-MM). 

  
The 27” deep Worksurface sides require 31” deep 
Uprights (6L07, 7L07, 8L07). 
  
Determine the desired location of the 

Corner Hook-on  

Worksurface

. The 36” deep Worksurface can be posi- 

tioned at a height from 27” to 31” in 1” increments. This 
limit is due to the requirement of Aluminum Top Supports 
with 36” deep surfaces. 
  
The 26.9” deep Worksurfaces can be positioned in 1” 
increments to suit your needs. Typical heights, floor to the 
top of the surface are: 
           
          Seated position ..........29”    
          Standing range............36” - 40”  
                                                  
Using the 5/32” Allen wrench , remove from the Upright 
any 1/4”-20 x 3/8” Button head cap screws that would 
interfere with the placement of the Hook-on Surface. 
  

NOTE

: All Corner Hook-on Worksurfaces require three 

              supports, one installed to each connecting side 
              and the third in the corner (Corner post).  See       
              

Figure 2

. 

  

Important 

The depth of the Hook-On Corner Worksurfaces is .30” 
less than the depth of Linear Hook-On Surfaces. This is 
to eliminate an interference with the corner post.

 

 
 
  
  
 

Corner Worksurface 

Integrated Corner Worksurface 

Figure 1 

Surface supports 

Surface supports 

Figure 2 

Intermediate support 
(not required on 36” x 36” 
worksurfaces) 

82355 

Integrated coner 
worksurface (L.H.) 

Integrated coner 
worksurface (R.H.) 

   Corner 
worksurface 

   Corner 
worksurface 

 
 

  

technical furniture 

D-5 

Содержание LMS











































































































































































































Отзывы:

Нет отзывов