manualshive.com logo in svg

Eaton LMS, Руководство по установке, Страница: 116 / 202

Поделиться
Скачать
Eaton LMS Скачать руководство пользователя страница 116

    

DOOR ALIGNMENT ADJUSTMENT IF  

    NECESSARY 
  
    

If the Door is mis-aligned within the Lan Locker ll  

    enclosure with an uneven space between the Door and  
    the Top and Bottom as shown in 

Figure 4

, one or  

    more of the following adjustments must be made. 
  
    A. Check the Full Frame and the Lan Locker ll  
         enclosure to ensure that they are level. Adjust as  
         required. 
     
    B. Ensure that both Side Panels are fully seated in 
         the slotted standards. Use a plastic mallet to tap 
         the Side Panels downward. 
     
    C. If one Side Panel remains remains higher than the 
         other, loosen all of the 1/4”-20 x .75” Phillips head 
         machine screws which fasten the hook plates to the  
         Side Panels. See 

Figure 5

. 

  
         Tap the top of the Side Panel with a plastic mallet  
         to adjust it and then re-tighten the 1/4”-20 screws. 
         Adjust the opposite Side Panel in the same manner 
         if necessary. 
 
    D. The Door can be adjusted up or down within the 
         Lan Locker ll enclosure by loosening the #8AB x  
         .50” Phillips head screws. See 

Figure 5

. Re- 

         tighten the screws after adjusting the door. 
  
  
                                                                                                           

Figure 4 

Uneven space 

Top 

Bottom 

Side panel 

Door 

Side panel 

Figure 5 

1/4” x .75” Phillips 
head machine screws 

  
1. Remove the protective liner paper from both sides 
    of the Plexiglass door panel.  
  
    If static build-up causes a problem with the attraction 
    of dust particles, it is recommended that the following  
    or similar anti-static cleaner and polisher be used. 
    Wright Line recommends: 
  
   

 KLEENMASTER BRILLIANIZE 

 

    Chemical Products Co. Inc. 
    Omaha, Nebraska                                                                                                                                                                             
  

Hook plates 

Slotted standard 

Door 

Hinge 

#8AB x 1/2” Phillips 
head screw 

r a c k   m o d u l e   d o o r  
( c o n t . )  
 

R a c k   M o u n t   M o d u l e  
P l e x i g l a s s   D o o r  
( c o n t . )  

82032 

 
 

  

technical furniture 

K-13 

Содержание LMS











































































































































































































Отзывы:

Нет отзывов