manualshive.com logo in svg

Eaton LMS, Руководство по установке, Страница: 13 / 202

Поделиться
Скачать
Eaton LMS Скачать руководство пользователя страница 13

F r a m e   L i n k i n g   K i t  

Please read these instructions carefully and follow 
the installation steps in sequence. 
  

Tools Required 
   

- 3/8” Open end wrench 

   - 7/16” Open end wrench 
   - 1/2” Open end wrench 
   - 5/32” Allen Wrench 
   - Plastic mallet 
   - Level 

 
 

  

technical furniture 

87467 

#54348 
1/4”-20 x 1/2” Hex 
Washer Head Screw 

#87464 
1/4”-20 x 3.00” Button 
Head Cap Screw 

#87466 
1/4”-20 Hex Nut 
w/Lockwasher 

#84741 
1/4”-20 x 1-3/4” Button 
Head Cap Screw 

IMPORTANT SAFETY INSTRUCTIONS

 

  
1. Maximum loading: (Evenly distributed loads on worksurfaces and shelving.) 
  
    (2) 72” x 84” Frame sections = 2000#/section. 
    (3) 72” x 84” Frame sections = 1700#/section. 
  

    NOTE

: If worksurfaces are not part of the installation, the maximum loading decreases to 1600# /section for two sections 

                 and 1200# /section for three sections.  The reduction is due to the Front Support not being used. 
 
2. Maximum number of frame sections that can be linked is three (3). 
  
3. Each frame joint must have the following components properly installed: 
  
    (1) Top Connector with centering screw. (Remove centering screw after installation.) 
  
    (1) Bottom Connector with leveler. 
  
    (1) Add-On Foot 
  
    (1) Front Support  
  
          Frame joint hardware (1/4”-20 x 3.00” button head cap screws and 1/4”-20 hex nuts). 
  
4. A minimum of two people are required for assembly.   
 

Fasteners That You Will Be Using 

Frame Linking Kit 

87467 

A-10 

Содержание LMS











































































































































































































Отзывы:

Нет отзывов