manualshive.com logo in svg

Eaton LMS, Руководство по установке, Страница: 157 / 202

Поделиться
Скачать
Eaton LMS Скачать руководство пользователя страница 157

2 

INSTALLATION OF THE CABLE TROUGH 
CORNER 

 
The 

Cable Trough Corner 

is required when using 

the  
Cable Trough in conjunction with a Tech Corner  
configuration.  The Cable Trough Corner is meant to  
go on the outside of the configuration. 
 
 
1. To install the Cable Trough Corner, the Cable   
    Trough sections must first be installed, without the   
    Cross Ties, at the same height.  From the top, place   
    the corner section inside the straight sections.   
    Gently pull back on the outside of the straight  
    sections and push the Trough Corner into place.    
    Release the straight sections. Secure using the two   
    clamps and screws. See 

Figure 3

. 

 
2. Install the Cross Ties (refer to previous page).   
 

INSTALLATION OF THE END PANEL

 

 

     1. The Cable Trough must first be installed without the  
         Cross Ties.  Identify the right 

End Panel 

by holding     

         the panel in front of you so the angled side points to    
         your left.  The vertical wires should be facing you.     
         From above, install the right End Panel by sliding it   
         down into the Cable Trough.  The top horizontal bar   
         should be resting on top of the Cable Trough.  Install  
         the left End Panel in the same manor.  See 

Figure 4

. 

 
         The End Panel will take the place of the end Cross   
         Ties.  Install the remaining Cross Ties ( refer to pre- 
         vious page).    

         

 

 

End panel 

Full frame 

Cable trough 

Cable trough 
corner 

Straight cable 
canal section 

Tech corner 

Clamp-outer 

Clamp-inner 

#10-24 x .38 
Machine screws 

C a b l e   T r o u g h  
C a b l e   M a n a g e m e n t  
( c o n t . )  

Figure 3 

Figure 4 

83481 

 
 

  

technical furniture 

M-22 

Содержание LMS











































































































































































































Отзывы:

Нет отзывов