manualshive.com logo in svg

Eaton LMS, Руководство по установке, Страница: 168 / 202

Поделиться
Скачать
Eaton LMS Скачать руководство пользователя страница 168

1 

2 0   A m p   P o w e r  
S t r i p  

  

INSTALLATION

 

 
The 

LPS7-00

 is a 5 duplex outlet (20 amp. rated) Power 

Strip that can be mounted vertically on any 72” and 84” 
high Full Frame configuration.  The Power Strip can be 
mounted on any vertical frame member of a Tech 
Frame, Rack Mount Module, or LAN Locker II.  
Installation on all vertical frame members is the same 
with two possible installation scenarios outlined below: 
 
1.  The Power Strip includes two to three 

Mounting  

     Clips

 and two to three 

#8-32 Self tapping screws

  

     that will attach it to the Frame. See 

Figure 1

.  

     Position a Mounting Clip in the highest position,  
     centered on the Standard, and mark this point with a  
     center punch. See 

Figure 2

.     

 
2.  Drill three holes in the Double Standard and then at- 
     tach two to three Mounting Clips with the #8-32  
     screws. See 

Figure 3

. 

 
3.  The Power Strip snaps onto the Mounting Clips.    
     See 

Figure 4

. Once the Power Strip is attached to  

     the Mounting Clips, a flat head screwdriver will be  
     needed if the Power Strip is to be removed from the  
     Mounting Clips. 
 
    

NOTE

:  The Mounting Clips attach  to the Single   

               Standard in the same manner as the Double  
               Standard.  Since there is no feature on the  
               Single Standard that denotes its center, care  
               needs to be taken to ensure that the Mounting  
               Clips are centered on the Standard and they do  
               not interfere with the Upright or Side Frame  
               screws. See 

Figure 2

.   

Tools Required

 

     - Power drill 
     - .149 inch drill bit 
     - Philips head bit or screwdriver 
     - Center punch 

Figure 1. 

Mounting clip 

#8-32 Self tapping screws 

20A Power strip 
#LPS700, #LPS799, 
#LPS2420, #LPS2420T 

Figure 3. 

Figure 4. 

Tech frame with 
enhanced uprights 

Power strip 

Figure 2. 

Mounting hole 

Center line of 
double standard 

#8-32 screw 

Mounting clip 

Upright screws 

#8-32 screw 

Mounting clip 

81559 

 
 

  

technical furniture 

N-4 

Содержание LMS











































































































































































































Отзывы:

Нет отзывов