manualshive.com logo in svg

Eaton LMS, Руководство по установке, Страница: 105 / 202

Поделиться
Скачать
Eaton LMS Скачать руководство пользователя страница 105

R a c k   M o u n t   M o d u l e  
( c o n t . )  

1. Position the Side Panel in the desired location . Insert 
    the hooks in the Side Panel into the Slotted Standard 
    and push down. To assure the hooks are seated, tap the  
    rear corner with a plastic mallet or equivalent. See 

Fig- 

    ure 3. 

  

    NOTE

: 

    If you are installing a Side Panel with three or more 
    Hook Plates, it may be necessary to loosen the three 
    1/4”-20 screws securing the Hook Plates to the Side 
    Panel. This will allow the Hook Plates to be adjusted in   
    or out to engage the slots. 

Re-tighten the Hook Plates   

    securely

 

after the Side Panel is installed. 

  

2. Install the opposite Side Panel. Make certain that both  
    Side Panels are at the same level and firmly seated in the  
    Slotted Standards. 
  
3. Install six #10-24 x 1/2” Phillips head machine screws in  
    each Side Panel. Install 3 screws at the top and 3 screws at  
    the bottom of each panel. Leave approximately 1/8”(3mm)  
    of thread exposed. See 

Figure 3

. 

  
  

INSTALLING THE TOP/BOTTOM PANEL 
     
    

19” Rack Mount Modules have two 

Perforated Top

                               

    

Panels 

with the 10” and 17” high units. They have one  

    

Cable Access Bottom

 and one Perforated Top Panel     

    with heights 24” through 84”. 24” Rack Mount Modules  
    have one of each with all heights, 38” through 84”. 
  
    Top/Bottom Panels are interchangeable. If the cables are to 
    enter the Rack Modules from above or through the floor, 
    use the Cable Access Panel accordingly. If the cables enter  
    through the back, install the Cable Access Panel at the   
    bottom. They can be changed at any time without dismant-   
    ling the Rack Mount Module. See 

Figure 4

. 

  
    

NOTE

: An optional 

Fan Mount Top Panel

 is available. 

                 See page O-5  . 
  
     
      
  
 
  

INSTALLING THE SIDE PANELS 

         Figure 4 

Top/Bottom panels 

82021 

Figure 3 

Side panel, R.H. 

Hooks 

Slotted 
standard 

#10-24 x 1/2” Phillips 
head machine screws 

1/8” 

Side panel 

Screw 

Cable access 
bottom panel 

Perforated top 
panel 

 
 

  

technical furniture 

K-2 

Содержание LMS











































































































































































































Отзывы:

Нет отзывов