manualshive.com logo in svg

Eaton LMS, Руководство по установке, Страница: 188 / 202

Поделиться
Скачать
Eaton LMS Скачать руководство пользователя страница 188

T a s k   L i g h t  
( c o n t . )  

2. Remove the lens and bulb from the Task Light . 
    To remove the lens, push it up near the front edge 
    of the Task Light fixture. See 

Figure 2

. Remove  

    bulb by rotating it in either direction and then pull- 
    ing it away from the mounting sockets. 
  
3. Position the Task Light fixture against the Shelf  
    stiffener with the mounting screws protruding thru 
    the large ends of the “key hole” slots. Push the fix- 
    ture toward the back of the Shelf to seat the screws 
    into the narrow portion of the slots and then tighten 
    the screws. See 

Figure 4

. 

  
4. Now replace the bulb and the lens. The corrugated 
    surface of the lens is toward the bulb. See 

Figure 3

. 

  
    

Cable Clips

 are provided to route and secure the 

    Task Light cord. 
  
     

NOTE

: Fixture must be plugged into a  three pronged 

                   grounded outlet.

 

  

 

 

“key hole” slot 

Task light 

Figure 4 

Screws 

Shelf stiffener 

Cable clip 

Cord 

Figure 2. Removing lens and bulb 

Figure 3. Replacing lens and bulb 

Push here 

Task light housing 

Lens 

Bulb 

Mounting socket 

Push here 
first 

Corrugated surface 

 
 

  

technical furniture 

80954 

Q-2 

Содержание LMS











































































































































































































Отзывы:

Нет отзывов