manualshive.com logo in svg

Eaton LMS, Руководство по установке, Страница: 124 / 202

Поделиться
Скачать
Eaton LMS Скачать руководство пользователя страница 124

R a c k   M o u n t   S h e l f  
( c o n t . )  

    ROLL-OUT SHELF INSTALLATION

 

 
    

NOTE

: The 

Roll-Out

 is equipped with “

Lock Out  

    Slides

” and a “

Front Disconnect

” chassis member for  

    your convenience during assembly to the Rack Module. 
  
1. Assemble the Slide sections onto the Rack Module rails.     
    Slip the 

Mounting Brackets 

behind the screw head of 

    the Clip Nut. See 

Figure 4

.  

  
2. Snug the Clip Nut screws enough to retain the Slide, but  
    still allow it to move in and out. 

Do not tighten

. 

  
3. Tighten the 

Rear Mounting Bracket 

to the Slide screws 

    now (not the Clip Nut screws). 
  
4. Close the two sections of the assembled Slide. 
  
    Slide the shelf with the disconnect members into the  
    mounted section. See 

Figure 5

. 

  
    Push the shelf in until there is a click 
  
    Now extend it to its full length. 
  
    Push it in again until it is fully closed (the ends of the  
    three slide sections are even). The last two inches may 
    bind; just push. It should now slide in and out freely. 
  
5. Now tighten the Clip Nut screws or leave them snug. 
  
6. To remove the shelf and chassis rail, refer to 

Figure 6

. 

 
 
  

 

  

Figure 4 

Mounting  
bracket 

Clip nut 

Screw 
head 

Rail 

Slide to bracket 
screw 

.50 

.62 

.50 

.62 

.62 

4 Hole group 

See NOTE at Step 1 

Figure 5 

Figure 6 

Shelf 

Disconnect 
member 

Slide 

Push in 

R.H. Slide 

R.H. Chassis 
member 

82158 

 
 

  

technical furniture 

K-21 

Содержание LMS











































































































































































































Отзывы:

Нет отзывов