Eaton LMS Скачать руководство пользователя страница 166 | Manualshive

Страница: 166 / 202

Eaton LMS Скачать руководство пользователя страница 166

3

3. Install the Power Strip assembly into the Cable Manage-
ment Component as shown in

Figure 3

. The Mounting

Clip/Plate assembly will snap into place at the bottom
of the Component as shown in

Figure 3

(detail).

NOTE

: If the Base Plates do not snap into place easily,

simply push harder. If they are too loose and do not stay
in place, it is possible to tighten the fit of the Base Plates
by bending the “wings” of the Base Plates outward.

The Power Strip can slide to any position along the length
of the Cable Management Component.

4. To remove the Power Strip, slide it out of the end of the
Cable Management Component.

Figure 3

Figure 4

Mounting clip

Open Frame

Double standard

#8-32 Screw
#18618
Qty. 2-3

Distance between Mounting clips
(see step 1)

VERTICAL INSTALLATION

The Power Strip can be mounted on any vertical frame
member of a Full/Open Frame, Rack Mount Module or
LAN Locker II. Installation on all vertical frame members
is the same with two possible installation scenarios out-
lined below.

1. Position a Mounting Clip at its highest location, centered
on the

Double Standard

, and mark this point with a cen-

ter punch. To position the second Clip, refer to step 2,
page_ for the correct location. See

Figure 4

.

2. Drill two holes in the Double Standard and attach the
Mounting Clips with the #8-32 Screws provided. See

Figure 4

.

Power strip
assembly

Cable management
component

Power strip
assembly

81559

L o w P r o f i l e
( 1 5 a m p )

technical furniture

N-2

«
...
164
165
166
167
168
...
»

Содержание LMS











































































































































































































Отзывы:

Нет отзывов