manualshive.com logo in svg

Eaton LMS, Руководство по установке, Страница: 31 / 202

Поделиться
Скачать
Eaton LMS Скачать руководство пользователя страница 31

-7- 

s u r f a c e   f i l l e r  

1.  Fasten the 

Mounting Plate

 to the Surface 

     Filler

 

using two of the #10 Phillips head 

     screws provided. See 

Figure 1

. 

  

 
2.  Position the Surface Filler Assembly   
     between two surfaces and flush off the  
     fronts. 
  
3.  Mark the four hole locations and remove 
     the Filler Assembly. 
  
4.  Drill four 1/8” diameter holes 1/2” deep. 
  
5.  Install the Filler Assembly with the four 
     remaining #10 phillips head screws. See   
     

Figure 2

. 

 

Surface Filler 

Figure 1 

Mounting plate 

#10 Phillips head screws 

Surface filler 

Figure 2 

Surface filler assembly 

#10 Phillips head screws 

Worksurfaces 

Flush 

Tools Required 

     - Phillips head screwdriver 
     - Electric drill 
     - 1/8” Drill bit 

NOTE

: This 

Surface Filler

 is designed to be 

              compatible with Standard Uprights only. 
              It is not compatible with Enhanced Up- 
              rights.  
  
 

 

 
 

  

technical furniture 

81489 

Содержание LMS











































































































































































































Отзывы:

Нет отзывов