manualshive.com logo in svg

Eaton LMS, Руководство по установке, Страница: 61 / 202

Поделиться
Скачать
Eaton LMS Скачать руководство пользователя страница 61

W o r k s u r f a c e   F i l l e r  
 

 

Tools Required

 

      -Phillips head screwdriver 
      -Electric drill 
      -1/8” Drill bit 
 

PLEASE NOTE: 

•     

Worksurface Fillers 

can only be used on 

Worksurfaces located 29” or more from the floor. 

•     

Worksurface Fillers can only be used where two    

        adjacent Worksurfaces are located on either side of 
        an upright. 

•     

The adjacent Worksurfaces must be located at the 

        same height from the floor. 
 
 

IMPORTANT:

 

36” and 42” deep Worksurfaces usually require 

#MA01-MM Aluminum Top Supports

.  If the 

Worksurface Filler is going to be installed in 
conjunction with a Top Support, the Top Brackets 
included with the Worksurface Filler must be used 

instead of

 the Top Brackets included with the 

Aluminum Top Support. 
 
Before assembling the Aluminum Top Support to the 
tubular stabilizers, assemble the appropriate 
replacement Top Brackets to the support. Use two #10-
24 x 1/2” Phillips head machine screws for each 
Bracket. See 

Figure 1

. 

 
Complete the installation of the Top Support as 
instructed in the Top Support instruction sheet. 

The top 

of the support should align with the bottom of the

 

worksurface. 

 

Replacement Top Brackets are

 not

 supplied with 27” 

deep and 30” deep Worksurface Fillers.

 

 
 

WORKSURFACE FILLER INSTALLATION 

 
1. Position the Worksurface Filler between the adjacent  
    Worksurfaces. The front bracket flanges should rest  
    under the surfaces. Align the “bull nose” of the Filler  
    with the “bull nose” on the surfaces. Mark the  
    location of the bracket holes and carefully drill two  
    1/8” diameter by 1/2” deep pilot holes. 
 
2. Attach the Filler using two #10 x 3/4” Phillips head  
    wood screws at the front bracket. Use two #10 x 3/8”  
    Phillips head thread forming screws to attach the  
    rear of the filler to the worksurface brackets. See  
    

Figure

 

2

. 

 

Worksurface Filler 

Figure 2 

Worksurface 
filler 

#10 x 3/4” Phillips 
head wood screws 

#10 x 3/8” Phillips 
head thread forming 
screws 

Worksurface 
bracket 

“Bull nose” 

Front bracket 
flange 

Worksurface 

Figure 1 

Plastic insert 

Top support 

Clamp 

Replacement top 
bracket 

#10-24 x 1/2” Phillips 
head machine screws 

85022 

 
 

  

technical furniture 

D-14 

Содержание LMS











































































































































































































Отзывы:

Нет отзывов