manualshive.com logo in svg

Eaton LMS, Руководство по установке, Страница: 177 / 202

Поделиться
Скачать
Eaton LMS Скачать руководство пользователя страница 177

I n t e r a c t i v e   M o n i t o r  
A r m   ( c o n t . )  

ATTACHING THE MONITOR PLATFORM

 

  
3. Place the thin plastic washer (packaged with the short  
    arm) over the 1.18” dia. pin on the Post or Beam Mount. 
    See 

Figure 4

. 

  
4. If you have the long arm version, assemble the arm ex- 
    tension to the short arm. The thin washer (packaged with 
    the arm extension) goes over the 5/8” pin. 
  
    Insert the pin of the extension into the end hole of the   
    short arm. Secure that assembly by inserting the M8  
    screw, the lock washer, and countersunk trim washer into 
    the end of the 5/8” pin. 

Do not tighten 

; The arm must 

    rotate.     

5. The Monitor Platform drops into the end of the arm.     
    Be sure two large black nylon spacers are on the plat- 
    form pin before inserting. Secure that assembly by in- 
    serting the M8 screw with the lock washer and counter- 
    sunk trim washer into the end of the 5/8” pin. 

Do not 

    over tighten

.      

ADJUSTMENTS

 

  
If rotated clockwise, the 

Monitor Platform

 will tighten it- 

self. If this happens, turn it counter clockwise 360 degrees 
or until loose. The platform should now turn freely within  
your operating radius. 

The Monitor Platform has three adjusting knobs under- 
neath. These are for leveling the platform if the monitor 
is tipped slightly in any direction. By loosening and tight- 
ening the knobs in some order, level can be attained. For 
example. if the monitor leans to the left (low side), loosen 
the low side knob(s) and tighten the high side drawing it 
down. 

Figure 4 

Monitor platform 

Adjusting knobs 

Support arm 
(short arm shown) 

Thin plastic 
washer 

Post/beam mount 

Lock washer 

Countersunk 
washer 

M8 Screw 

1.18” Pin 

Platform pin 

Nylon spacers 

82454 

 
 

  

technical furniture 

P-2 

Содержание LMS











































































































































































































Отзывы:

Нет отзывов