Eaton LMS Скачать руководство пользователя страница 153 | Manualshive

Страница: 153 / 202

Eaton LMS Скачать руководство пользователя страница 153

Tools Required

-Phillips Head Screw Driver
-Plastic mallet

APPLYING TO LMS BASIC

1. The rear of the

Post

has a row of small holes. Align

the
holes (every other hole) in the

Mounting Channel

with the Post holes and attach with the #8 screws.

Starting at the top

, snap the

Cable Management

Duct

into the channel.

NOTE

: It is meant to be a

tight
fit, so use of a mallet and block to tap the duct in place
may be necessary. Once started, continue taping it in,
moving down a few inches at a time. See

Figure 1

.

2. Install the

Cover(s)

.

TO FULL FRAME

1. This kit can be used to apply

Vertical Cable

Management

to unused portions of the

Intermediate

Standards

(double rows of slots). It can also be cut

into smaller pieces and applied between components.
Attach the Mounting channel with double sided tape.
See

Figure 2

.

CAUTION!

Once applied, do not remove and re-stick

the tape. The bond strength diminishes greatly.

2. Remove the protective paper from one side and
apply four (84” units) pieces of tape to the
Mounting Channel first. Then, remove the
remaining protective paper from the tape and
starting from one end, carefully stick the
channel to the standard. Snap the duct into
place as described above. See

Figure 2

.

3. Install the Cover(s).

Figure 2

Mounting
channel

Double sided
tape

Cable management
duct

Cover

Intermediate
standard

Trapezoidal
holes

Full frame

82604

Figure 1

#8 Screws

Cable management
duct

Mounting channel

Cover(s)

Post

Basic unit

L M S   B a s i c
C a b l e   M a n a g e m e n t
K i t

technical furniture

M-18

«
...
151
152
153
154
155
...
»

Содержание LMS











































































































































































































Отзывы:

Нет отзывов