Eaton LMS Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 202

Eaton LMS Скачать руководство пользователя страница 49

-3-

L i n e a r   H o o k - o n
W o r k s u r f a c e s
( c o n t . )

Top support
bracket

Open frame

1/4”-20 x 1/2”
Machine screws

Stiffener

1/4”-20 x 1/2”
Hex head

Linear Hook-on Worksurfaces

can be installed at any height at one

inch increments. The recommended Worksurface height is 29 or 30
inches off the floor.

There are three different configurations that 27 and 36 inch deep
Hook-on Worksurfaces can be attached. Each configuration will vary
in the installation procedure. Different depth Worksurfaces will
require additional hardware when installed.

1. Determine what height the Worksurface will be by measuring
from the floor to the top of the hook-on

Top Support Bracket

and adding 1.00 inch.

2. Attach the Top Support Bracket to the Full Frame and tap it into
place with a plastic mallet to make sure the hooks are securely
seated. See

Figure 1

.

3. Locate the small hole inside the back of the Top Support Bracket
and insert the 1/4”-20 x 1/2” Hex head screw with a 3/8” socket.
See

Figure 2

.

If you are installing two worksurfaces on one Full Open Frame,
Extended Top Support Brackets are needed. Refer to the next
page before

proceeding.

If the Hook-on Modesty Panel option is used, please go to page
___for additioal instructions.

4. For Worksurfaces that are longer than 60” in length, a

Stiffener

needs to be installed. Position the Stiffener as shown in

Figure

2

. Attach the Stiffener to the Hook-on Top Support Brackets

using the 1/4”-20 x 1/2” Machine screws.

NOTE

: If you are installing the Worksurface with a

Modesty

Panel

, the stiffener is not needed.

5. Position the Worksurface on the Top Support Brackets so it is
flush with the frame and centered between the uprights. Make
sure that all of the Top Support Brackets are at the same height.
The holes in the brackets will correspond to pilot holes in the
top. Secure the Worksurface to the brackets using the #10 AB
x .75” Phillips head screws.

Tools Required

  - Phillips head screwdriver
  - 3/8” Socket with extension
  - Plastic mallet
  - Measuring device

Figure 3

Open frame

Worksurface

#10 AB x .75
Phillips head screws

Top support bracket

Stiffener

Figure 2

82354

technical furniture

Figure 1

Trapezoid

Hooks

Top support bracket

1”(25.4mm) less than
desired height

R.H. upright assembly

Open frame

D-2

«
...
47
48
49
50
51
...
»

Содержание LMS











































































































































































































Отзывы:

Нет отзывов