manualshive.com logo in svg

Eaton LMS, Руководство по установке, Страница: 20 / 202

Поделиться
Скачать
Eaton LMS Скачать руководство пользователя страница 20

85360 

Please read these instructions carefully and follow 
the installation steps in sequence. 
  

TOOL TRACK INSTALLATION

 

  
Tool Tracks

 may be installed on Low Profile Overhead 

Brackets (MA50-MM) or on High Profile Overhead 
Brackets (MA51-MM) which are ordered separately. 
  
Tool Tracks may be installed on LMS Full Frames or 
TechOrganizer frames.  
  

IMPORTANT

: Maximum Tool Track loading is 50 lbs. 

  

Tools Required

: 

       -5/32” Allen Wrench 
       -1/2” Wrench 
       -Soft mallet 
  
1. Determine the desired Tool Track location and hook 
    on the first Overhead Bracket. Space the second Brac- 
    ket based on the Tool Track size, 36”, 48” etc. Tap 
    the Brackets down to make sure that the hooks are 
    seated. Secure the Brackets to the Frame using the 
    #10-24 x 3/8” screws provided. See 

Figure 1

. 

  
2. Position the Tool Track under the Overhead Brackets 
    and align the holes in the Track with the holes in the  
    Brackets. Attach the Tool Track using the 1/4”-20 x 
    1/2” screws and lock washers Tighten both screws 
    securely. See 

Figure 2

. 

  
3. Insert one 

End Stop 

into the Tool Track (see 

Figure

 

    

2

 for orientation). The bottom flat plate is outside the 

    Track  to clamp the Stop in place. 
  
    Install an 

End Cap

 into the Tool Track and slide the 

    End Stop to the End Cap and lock in place by tighten- 
    ing the two nuts on the Stop. 
  
4. At the opposite end, insert the 

Balancer Trolley

 into   

    the Track and then install the second End Stop and  
    End Cap following the instructions in step 3. 
  

NOTE

: If an End Cap strikes a screw head before seat-  

              ing fully into the Tool Track, trim the Cap with 
              scissors. 
  
              
  

Tool Track 

Figure 1 

#10-24 x 3/8” Pan head 
screw 

Full frame 

Overhead  
bracket 

Overhead  
bracket 

Full frame 

Figure 2 

Balancer 
trolley 

End stop 

End cap 

Tool track 

Bottom flat  
plate 

End cap 

End stop 

Lock washer 

1/4”-20 Button head 
cap screws 

T o o l   T r a c k / T o o l   J i b  

 
 

  

technical furniture 

A-18 

Содержание LMS











































































































































































































Отзывы:

Нет отзывов