manualshive.com logo in svg

Eaton LMS, Руководство по установке, Страница: 171 / 202

Поделиться
Скачать
Eaton LMS Скачать руководство пользователя страница 171

K e y b o a r d  
S u p p l e m e n t  

Tools Required 

      - Phillips head screw driver 

MOUNTING TO UNDERSIDE OF BASIC PLUS 
LAMINATE SHELVES 

1. Align the 

Track

 mounting holes to pre-drilled holes  

    on the underside of the Laminate Shelf Stiffener.  Four  
      of the middle holes in the track will line up with holes 
      in the stiffener.  See 

Figure 1

. 

 
2.   In the remaining holes, snap spacers into the track as 
      shown in 

Figure 1. 

 

3.   Using the #8 x 1/2” screws, attach the Track to the 
      stiffener.  Install two #8 x 1.25” screws along each 
      side of the Track and a rear center screw with a 
     

Bumper

. The #8 x 1.25” screws will screw through 

      the spacer into the laminate shelf.  Make sure the
      screws are drawn down tight enough to ensure 
      proper clearance between the 

Articulating Arm 

      Mechanism 

and the track. 

  
4. Mount the 

Keyboard Platform

 to the tray brackets 

    of the Articulating Arm Mechanism. Install six screws 
    into the pre-drilled holes in the underside of the 
    Platform. 

  
5. Loosen the knob and lower the mechanism to the 
    down position. Re-tighten the knob. 
 
6. Slide the mechanism into the grooves on the Track 
    until it contacts the Rear Bumper. 
  
7. Install the 

Front Bumper

 with the #8 x 1.25” 

      screw. 
  
8. Apply the 

Warning Label

 as shown. 

  
9. 

Cord Clips

 are provided for wire management. 

  
NOTE: For smooth sliding operation, it may be  
             necessary to apply a light layer of lubrication 
             to both sides of the Track. Slide the mechan- 
             ism back and forth to spread the lubrication. 
  
* Keyboard mechanism intended for keyboard  
   weights only. 

NOTE

: For non-standard application, use the Track 

              as a drill template. Keeping the Track per- 
              pendicular to both edges, position it 1/2” 
              from the front edge of the shelf. Drill (10) 
              .109 dia. holes. 

Figure 1 

Keyboard platform 

Articulating arm 
mechanism 

Tray brackets 

Pre-drilled holes 

Bumper 

* Label 

Basic plus Laminate Shelf 

Knob (up & down adjustment) 

#8 x 1.25” Phillips head screw 

 

Bumper 

#8 x 1.25” Phillips head screw 

Track 

#8 x 1/2” Phillips head 
screws 

Laminate Shelf Stiffener 

Spacer 

69871 

 
 

  

technical furniture 

O-2 

Содержание LMS











































































































































































































Отзывы:

Нет отзывов