manualshive.com logo in svg

Eaton LMS, Руководство по установке, Страница: 179 / 202

Поделиться
Скачать
Eaton LMS Скачать руководство пользователя страница 179

A r t i c u l a t i n g   A r m /  
C o m p o n e n t s  

86427 

Please read these instructions carefully and follow 
the installation steps in sequence. 
  

Tools Required 
     

- Phillips head screwdriver 

     - 3/16” Allen wrench (provided) 
     -5/32” Allen wrench (provided)  
     - Rubber mallet 
  

ATTACHING COMPONENTS TO ARM 

  

Monitor Platform 

  
1. Remove the 5/16”-18 x 1/2” Button head cap screw 
    and washer from the shaft located on the bottom of  
    the Monitor Platform. Use the 3/16” Allen wrench 
    provided. See 

Figure 1

. 

IMPORTANT SAFETY INSTRUCTIONS 
  

1.

 Do Not

 exceed the maximum weight load capacity for any component. 

  
                   

Component                                           Maximum Capacity 

               Monitor Platform                                                  60 Lbs. 
               Tool Tray                                                              30 Lbs. 
               Bin Board                                                             30 Lbs. 
               Peg Board                                                             20 Lbs. 
               Document Holders                                                20 Lbs. 
  
2. 

Do Not

 install a Monitor Platform, Tool Tray or Bin Board on the 24” or 30” wide free standing TechBench or Linx  

    Worksurface. They may cause the unit to tip if they are fully loaded and extended to one side.  
  
    The Bench or Worksurface must be securely attached to an adjacent unit to prevent potential tipping. 
  
3. 

Do Not 

extend the components beyond the back of the 24”, 30” or 36” wide TechOrganizers on Linx Worksurfaces 

    as the unit may tip.  
  
4.

 Always 

ensure that the articulating arm is secured to the TechOrganizer or Full Frame using the #10-24 x 3/8” thread 

    forming screw provided. 
  

Monitor Platform 

 
 

  

technical furniture 

P-4 

Articulating Arm/Components 

Содержание LMS











































































































































































































Отзывы:

Нет отзывов