Eaton LMS Скачать руководство пользователя страница 25

Страница: 25 / 202

R e t r o f i t K i t
N o v a

86270

Please read these instructions carefully and follow
the installation steps in sequence.

NOTE

: The Trim Ring provided with the Nova01 and

Nova06 kits can not be used with Linx Worksurfaces.
Please discard Trim Ring.

Tools required

-Phillips head screwdriver

NOTE

: The wire rack is to be on the inside of the

Side Assemblies to create one left hand and one right
hand assembly. Refer to

Figure 1

for handing).

1. Attach the

Cross Braces

to the Side Assemblies

using eight #14AB x 3/4” screws. See

Figure 1

2. Attach the

Legs

(optional)

to the Side Assemblies using

four #14AB x 3/4” screws and then install the

Levelers

(optional)

on each leg. See

Figure 2

NOTE

: Legs are not provided with the Oversized Nova

kits. Install the four Levelers directly into the
Side Assemblies.

technical furniture

#14AB x 3/4”
screws

Side assembly

#14AB x 3/4”
screws

Cross brace

Figure 1

Figure 2

Side assembly

Leg

Leveler

#14AB x 3/4”
screws

Side assembly

Nova Retrofit

A-22

Содержание LMS











































































































































































































Результаты поиска

Содержание LMS

Отзывы:

Eaton LMS, Руководство по установке, Страница: 25 / 202

Результаты поиска

Содержание LMS

Отзывы: