Eaton LMS Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 202

Eaton LMS Скачать руководство пользователя страница 36

87570

B-5

technical furniture

L M S F o u n d a t i o n s
( c o n t . )

4. Stand the Corner Post assembly up and and attach
the Cross Ties to the linear unit with eight 1/4”-20 x
2.00” hex washer head thread cutting screws and
tighten securely. See

figure 7

.

5. Continue adding sections using the methods shown
in steps 1 thru 4.

6. Check all screws to ensure that they have been fully
tightened.

7. Adjust the levelers as necessary to level the unit.

The 48”, 60” and 72” wide units can be segmented into
the following modules.

48” Unit = (2) 24” Modules

60” Unit = (2) 30” Modules

72” Unit = (3) 24” Modules
= (2) 36” Modules
= (1) 24” Module, (1) 48” Module

1. Locate the appropriate hole patterns in the Cross Ties
and attach the two

Intermediate Standard

halves to

the top/bottom Cross Ties with eight 1/4”-20 x 1-1/2”
flat head socket cap screws and tighten securely. See

figure 8

.

2. Complete the assembly by installing #10-24 x 1-1/2”
flat head socket cap screws at the pre-punched loca-
tions on both the front and back halves of the Inter-
mediate Standards and tighten securely. See

figure

8

.

3. Adjust the leveler(s) at the bottom of the Intermediate
Standard(s).

INTERMEDIATE STANDARDS

Figure 7

Figure 8

Corner post assembly

Linear unit

Top cross tie

Intermediate standard half

#10-24 x 2-1/2” flat
head socket cap screws

Bottom cross tie

1/4”-20 x 1-1/2” flat
head socket cap screws

1/4”-20 x 1-1/2” flat
head socket cap screws

Leveler

«
...
34
35
36
37
38
...
»

Содержание LMS











































































































































































































Отзывы:

Нет отзывов