manualshive.com logo in svg

Eaton LMS, Руководство по установке, Страница: 154 / 202

Поделиться
Скачать
Eaton LMS Скачать руководство пользователя страница 154

Wire tie 

Tower or Electronics 
shelf 

Hole 

Wire tie  
base 

Screw 

Figure 3 

LA34-MM CABLE STRAP, SET OF 25 

 
1. These 

Cable Ties

 can be screwed (recommended)   

    to the rear of the LMS Basic Vertical Posts, using  
    the small vertical holes, or Cable ties can be  
    attached to the rear of Tower and Electronic  
    shelves.  Screwing it on provides easy removal for  
    relocation. 
 
2. Screw the 

Wire Tie Base

 to the Post, leaving the  

    bonding tape and protective paper in place for  
    future use. Cut the center of the tape so the screw  
    easily passes through.   
 
3. Slip the 

Wire Tie 

through the slots on the base and  

    it's ready to use. 
 
    If you choose to adhere the Wire Tie Base, be sure     
    the orientation is correct for the tie, remove the  
    protective paper, and stick it on.   
 
 
 

Post 

Hole 

Bonding tape 

Screw 

Wire tie 
base 

Wire tie 

Figure 3 

82604 

L M S   B a s i c  
C a b l e   M a n a g e m e n t  
K i t   ( c o n t . )  

 
 

  

technical furniture 

M-19 

Содержание LMS











































































































































































































Отзывы:

Нет отзывов