manualshive.com logo in svg

Eaton LMS, Руководство по установке, Страница: 87 / 202

Поделиться
Скачать
Eaton LMS Скачать руководство пользователя страница 87

L o c k i n g  
C o m p a r t m e n t  

RECEEDING DOOR INSTALLATION

 

  
1. Place the 

Receeding Door 

assembly face up on top of 

    the Locking Compartment. See 

Figure 5

. Position the 

    two 

Door Track 

hinges against the front flange of the 

    Top. The Door edges must be aligned with the outer sur- 
    faces of the End Panels. Align the slots in the Door Track 
    hinges with the six holes in the front flange of the Top. 
    Install and tighten six #8 Phillips head sheet metal screws 
    into the Door Track hinges to secure them. See 

Figure 5

.  

  
    To operate the Receeding Door, grasp the lower edge of 
    the door panel near the center and pull the door all the way 
    toward you. Carefully lower the door to the closed position. 
    Reverse this procedure to open the door. 
  
    

NOTE

: Never allow the Receeding Door to slam closed. 

                  Personal injury or damage to the unit may result. 

  

TOP INSTALLATION

 

  
1. Before installing the 

Top

, make sure that the three screws  

    at the top of each End Panel is backed out 1/8”(3mm) as 
    shown in 

Figure 3

.  

  
2. Position the Top between the End Panels above the screws. 
    

NOTE

: The Receeding Door mounting holes must face to- 

    wards the front. Lower the Top so that all six screws en- 
    gage their corresponding slots in the Top. Next, tighten 
    the screws to secure the Top. See 

Figure 4

.  

  

80172 

 

 
 

  

technical furniture 

G-2 

Figure 4 

Top 

Screws 

End panel 

Receeding door  
mounting holes 

Shelf 

Figure 5 

Front flange 

Receeding door 

Door track hinge 

#8 Phillips head 
screws 

End panel 

Door track 

Содержание LMS











































































































































































































Отзывы:

Нет отзывов